Consider the following parallel connected loads with the following characteristics L1: 1.2kW purely resistive L2: 2.5kW, 0.8 pf lag L3: 1.8kW, 0.72 pf lag Find the total real power (in kW) consumed by the parallel loads Find the total reactive power (in kVAR) consumed by the parallel loads Find the net power factor lag of the parallel loads Compute for the reactive power (in kVAR) needed to be supplied by a capacitor to increase the power factor to 0.92 lag

Consider the following parallel connected loads with the following characteristics L1: 1.2kW purely resistive L2: 2.5kW, 0.8 pf lag L3: 1.8kW, 0.72 pf lag Find the total real power (in kW) consumed by the parallel loads Find the total reactive power (in kVAR) consumed by the parallel loads Find the net power factor lag of the parallel loads Compute for the reactive power (in kVAR) needed to be supplied by a capacitor to increase the power factor to 0.92 lag

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
A Load absorbs 10 kVA at a leading power factor of 0.6. The complex power is: Select one: O a. 6000-j8000 VA O b. O c. O d. 10000 VA 8000-j6000 VA 2000-j8000 VA
During fast decoupled Method load flow analysis in one of the loads the calculated reactive power was found as - 0.8 p.u. and change in reactive power as -3.2 p.u. According to you which one of the following choices will have the value of Specified reactive power at the load bus? Select one: O a. -4.0 p.u. O b. -2.4 p.u O C.2.2 d. +4.0 p.u.
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a. -6000 - j8000 VA b. 6000 + j8000 VÀ c. 6000 - j8000 VÀ d. None of these
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
In a system of 132 kV, the circuit phase to ground capacitance is 0.2 uF and the circuit inductance 5H. The circuit breaker interrupts a magnetizing current of 5 A (peak value). Arrangement shown in figure V-79 kV L-5 H 0000 R-790 www CB CH0.32PPC Fault (F)
Question 6 20020°V L rms In the circuit in the figure; L load draws 15 kVA with lagging power factor 0.6. • The load L 2 draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the reactive power for the loadL ? 1 9000 O -3600 O 2700 O 12000 O 4800 O 4500 No new data has been saved. The latest contact is at16I01
please solve it with the load being 150 MW and - 50 MVar.
A given load takes 40 kVA at 50% lagging power factor, while another load is connected in parallel across the same source takes 80kVA at 86.7% lagging power factor. Find the apparent power
Assume that the load resistance can be varied between 0 and 4000 Ω andthat the capacitive reactance of the load can be varied between 0 and−2000 Ω. What settings of RL and XL transfer the most average powerto the load? What is the maximum average power that can be transferredunder these restrictions?