Need all parts correctly. Thank you... Consider the following plane stress state:Ox=-12 kpsi, Oy- 22 kpsi, Txy= 12 kpsi cwCalculate the following:1. The coordinates of the center of the Mohr's circle CThe location of the center of the Mohr's circle Cis (2. Principal normal stresses (01, 02)The principal normal stresses are 0₁ =3. Maximum shear stress (7)The maximum shear stress is4. The angle from the x axis to 01 (p)The angle from the x axis to 01 (p) is5. The angle from the x axis to T (s)The angle from the x axis to 7 (s) is6. The radius of the Mohr's circleThe radius of the Mohr's circle iskpsi.0kpsi.kpsi and 02 =CW.kpsi,CW.kpsi.kpsi).

Find outthe coordinates of the center of Mohr's circle C.Principal normal stress Maximum shear…

Consider the following plane stress state: Ox=-12 kpsi, Oy- 22 kpsi, Txy = 12 kpsi cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis 2. Principal normal stresses (01.02) The principal normal stresses are 0₁ = kpsi, kpsi and 2 = kpsi. kpsi).

Consider the following plane stress state: Ox=-12 kpsi, Oy- 22 kpsi, Txy = 12 kpsi cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis 2. Principal normal stresses (01.02) The principal normal stresses are 0₁ = kpsi, kpsi and 2 = kpsi. kpsi).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of crv = —45 MPa and rTb = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement