Consider the following rotational mechanical a. Apply the "by inspection" method in Laplace domain to write the system of equations that represents the dynamics of the system b. Solve for the output variable q1(s). Use Cramer's rule or the substitution method to solve for the output variable q1(s). c. Give the transfer function G(s) = 91(s)/T(s)

Consider the following rotational mechanical a. Apply the "by inspection" method in Laplace domain to write the system of equations that represents the dynamics of the system b. Solve for the output variable q1(s). Use Cramer's rule or the substitution method to solve for the output variable q1(s). c. Give the transfer function G(s) = 91(s)/T(s)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please
Consider the following spring system. m, C3 Cy m₂ C₂ Write the stiffness matrix K Write the matrix M ¹K C₁ = 6, m₁ = 6, C₂ = 12, m₂ = 3 Find the eigenvalues and eigenvectors of M ¹K: Smaller eigenvalue = with eigenvector • Larger eigenvalue = with eigenvector C3 = 18, C₁=6 If this spring system oscillates without any external forces present, then the position of each mass satisfies the following general formula: X 8 u(t) = (a₁ cos( t) + b₁ sin(t)) + (a2 cos (t) + b2 sin(t)) If the system begins oscillation with initial position u(0) = [] | and initial velocity (0) = [] then the position of the masses at time t is given by u₁(t): u₂(t):
6. The electro-mechanical system shown below consists of an electric motor with input voltage V which drives inertia I in the mechanical system (see torque T). Find the governing differential equations of motion for this electro-mechanical system in terms of the input voltage to the motor and output displacement y. Electrical System puthiy C V V₁ R bac (0) T bac T Motor - Motor Input Voltage - Motor Back EMF = Kbac ( - Motor Angular Velocity - Motor Output Torque = K₂ i Kbacs K₁ - Motor Constants Mechanical System M T Frictionless Support
1. write the transfer function of the differential equation. d'y 2dy2 3dy 3dx3 + dt4 X dt3 a.- + + 4y = dt² dt + 4x
Consider the following spring system. m. c2 = 10, c3 = , c4 = 2 C1 m2 = 2 Write the stiffness matrix K = Write the matrix MK Find the eigenvalues and eigenvectors of MK: • Smaller eigenvalue = with eigenvector • Larger eigenvalue = with eigenvector If this spring system oscillates without any external forces present, then the position of each mass satisfies the following general formula: u(t) = (a1 cos( t) + bị sin ( t) + (a2 cos( t) + bz sin( t) If the system begins oscillation with initial position u(0) = and initial velocity u'(0) = then the position of the masses at time t is given by u1(t) = uz(t) = Wir
Q5: Given the rotational system shown in below, find the transfer function G(s)= 01(s)/T(s) D K2 Please help ASAP. Pls show all steps and calculations. Make sure to find theta1(s)/T(s)
= = Problem #2 - Modeling, Mass-Spring System Two masses are connected by springs in series as shown in Figure 1 below where k₁ 20 N/m, k₂ = 10 N/m, m₁ 10 kg, and m₂ = 5 kg. Solve the system of ODEs in matrix form using the determinant to obtain the characteristic equation (it will make sense to substitute > for w² when you get to your characteristic equation). Determine the eigenvalues (frequencies) and eigenvectors (modes) of oscillation. Assume that no damping is present and that the masses slide without friction. On your diagram, sketch the modes of oscillation (think of how the masses could oscillate with respect to each other). What determines which mode or combination of modes that the masses oscillate at? i.) ii.) iii.) iv.) v.) vi.) vii.) Sketch the system and include a free body diagram. Use a conservation equation to develop your differential equation model (you should end up with two ODEs to describe the motion of both masses). Write your system of ODEs in matrix form. Set…
Write the differential equations of motion, convert to Laplace domain and find the transfer function indicated. Use: k1 = k2 = 4, m1 = m2 = 1, c=2 G(s) = %3D %| X2(s) Y(s)
(a) Consider following differential equation. d³y d²y d³x d²x dx +6,+ 8x dt2 dt dy +3- +5 +y = +4- dt3 dt² dt dt3 Find the transfer function of S) X(s)' i)
Get the equation of motion by drawing the free body diagram of the given systems. a) Get the system's transfer function and find the unit digit answer. Show all decals in detail. m = 1 kg b= 20 Ns/m k = 125 N/m F ww k b) get the transfer function of the system. X(s)/Pg(s) =? Show all decals in detail. resistance R k Pg massless piston area (A) capacitance
For the mechanical translation system below, find the transfer function O1/T and 02/T. Use the following values. K= 2+c D1 = 1 J1 = 3+a J2 = 2+b D2 = 5 where a 2 b= 5 C = oblems. T(t) 0(1) 02(1) D1 K D2
Find the ditferential equation from the transfer of the function for the Giving following system and draw the block diagram of the system. x(s) H(s) u(s) 0.5s + 1