Consider the "H" section shown in the figure below. 1) What is the distance to centroid (x¯)?   Please enter answer in mm and to 1dp

Q: The block of wood glued together as shown is subjected to a compressive force of P KN. Determine P…

A: Finding of The compresive load P in KN when and normal stress along glued  plane at 37o  with axis…

Q: differentiate between saturated and unsaturated flow in soils

A:

Q: 24. The reduced bearing of a 10 m long line is N30°E. The departure of the line is (a) 10.00 m (c)…

A: Length of line l = 10 m, Bearing N 30o E It is needed to find the departure of the line D.

Q: For a earth dam shown in Fig.(2), find the length of filter to make seepage lin contact with surface…

A: Seepage is flow of water under gravitational forces in permeable medium.

Q: (12-16) MOMENT DIAGRAM (DON'T FORGET TO PUT LABELS, UNITS, AND DEGREE OF CURVE CONSTRUCT SHEAR AND…

A: Given : Required : Moment diagram

Q: A hydroelectric dam is being planned with a Francis turbine. The engineers choose to geometrically…

A: The new turbine is geometrically similar to the existing turbine., The new penstock is also…

Q: Which Section of the Act or board rules most clearly directs an engineer regarding his or her…

A: Which Section of the Act or board rules most clearly directs an engineer regarding his or her…

Q: The pump system in the figure is drawing water from the tank₁ and pumping it into the tank2. Flow…

A:

Q: The block of wood glued together as shown is subjected to a compressive force of P=34 kN. Determine…

A:

Q: Draw the shear and bending moment diagrams for the beam and loading shown, and determine the maximum…

A: A beam is given we need to draw shear force and bending moment diagram

Q: CALCULATE AND DRAW THE SHEAR AND MOMENT DIAGRAM 120 KN 118m 48 m Į 120 KN 18 m

A: Given : To Calculate: SFD and BMD

Q: kN 2. A simply supported beam a W410 x 114 carries a uniform load of 12- and a concentrated load of…

A: Span, L = 10 m UDL, w = 12 kN/m fy = 250 MPa Sx = 2200 x 103 mm3 To find: The concentrated load of P…

Q: Draw the moment diagram for the beam and two columns. also make sure to show that the moment are on…

A: ### FOR Bending Moment Diagram for Frame by cutting frame into 3 parts###

Q: Find the necessary pipe diameter to transport 501/s of water (vw=1x10-6m²/s, Pw = 1000kg/m³), for a…

A: The problem is based on Darcy's-Weishbach formula and Moody chart. These kinds of problem are solved…

Q: What is the maximum velocity in kph of the car could pass thru an easement curve having a length of…

A: Curve length = 120 m The radius of central curve= 260 m We can use the empirical formula to…

Q: A toy is dropped into a pool of water (g = 9.81 = 9.81 m2, p = 1000 m). It is then submerged 3m.…

A:

Q: A 3.5 m D 7m B 2.5m *

A:

Q: A 0.2 mm thick tape goes over a frictionless pulley of 25 mm diameter as shown in figure. If E of…

A:

Q: A 3.5 m 7m B 2.5m DRAW THE INFLUENCE LINE DIAGRAM FOR: VD = f(x) Av = f(x) RB = f(x) INVOLVING A…

A: Consider a unit load moving from A to C

Q: Q (2) - The following data pertain to a Francis turbine: Net head = 70 m, Speed= 700 r.p.m, Shaft…

A:

Q: For the statically indeterminate beam shown in Figure 3, determine the reactions at the support A…

A: Indeterminate beam with half span loading, It is asked to determine the reactions at the support A…

Q: SOLVE ALL QUESTIONS FROM 16 TO 27 must solve all dont say for agàin post. Thanks. I will Upvote.…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Draw a moment diagram and determine the largest moment at support and field in the statically…

A: A statically indeterminate beam is given which is loaded with UDL of q kN/m throughout the beam. The…

Q: CALCULATE AND DRAW THE SHEAR AND MOMENT DIAGRAM 120 KN с 18 m A t 48 m £ Į 120 KN 18 m

A: The beam is subjected to Loading as shown in figure The free body diagram of the beam

Q: For 100 sq. m cement concrete (1: 2: 4) 4 cm thick floor, the quantity of cement required, is

A: →thickness = 4cm→Area of cement concrete =100m2→sum of ratio of concrete mixture =1+2+4=7To…

Q: A planar elastic structure is subjected to uniformly distributed load, as shown in the figure (not…

A: A planar elastic structure as shown- UDL=12 kN/m,Span=8 m, To Find- The value of the maximum…

Q: Determine the maximum reactions at Point A and B if the weight of the beam is 15 kn/m the moving…

A: Of maxm Reactions at Supports  A and B using ILD due to given loading system###

Q: PROBLEM #1: Determine the tension in each segment of the cable and the cable's total length. 7 ft 4…

A:

Q: Determine the displacement at point C by method of virtual work. El is constant. P P A BIN C + B

A: EI = constant Determine the displacement at point-C using Virtual work method.

Q: Q. 2) For the composite section show below, (a) Determine the centroid xc and yc with respect to the…

A: Let 1 be the triangle, 2 be the rectangle, 3 be the semicircle and 4 be the circle.

Q: Draw the shear force and tension side bending moment diagrams for the structure shown in Figure 1…

A:

Q: 3 10kN/m SKN/M B 5m 6m 5 kN/ 5m D S-f

A:

Q: 2- Draw the shear force and bending moment diagram for the beam as shown below 10 kN/m ↓▬▬▬▬ 15 m-…

A:

Q: Calculate the principal normal stress values, the principal normal stresses and the stresses that…

A:

Q: 4. The development length of a deformed reinforcement bar can be expressed as φσ, (0) From the bd…

A: Deformed reinforced bar- Development length  Ld=1kϕσs4τbd Value of k=?

Q: Draw the figure of level and show its parts on it.

A:

Q: Q2 Draw the Bending moment only for the beam shown 400N 600N 2m 2m D 2-S 2m B A DO he B.M.

A: Draw the bending moment diagram of the beam.

Q: What differences would be expected when sampling with a angle gauge or angle prism (point sampling)…

A: Angle gauge or angle prism sampling (also known as point sampling or variable radius plot sampling)…

Q: Calculate the coefficient of permeability of a soil sample of 6 cm is height and 50cm2 in cross…

A:

Q: Qus- The total, neutral and effective vertical stresses (in t/m²) at a depth of 5 m below the…

A: Total Stress -  At any given plane section in the soil mass Total stress is due to the Total wt. if…

Q: A hydraulic machine exerts a force of 900N on a piston of diameter 1.80cm. The output force is…

A: Force F1=900 N, Piston diameter d1=1.80 cm, For output- Piston diameter d2=36 cm, To Find- The value…

Q: A W8x67 is used as a column. The weak axis is braced at 30 ft from the bottom and the bottom end…

A:

Q: Determine the location of the centroid of the symmetrical composite section, as shown in the…

A:

Q: Calculate the member forces for the following diagram using method of joints. 3 m 3 m B A Ay 7m 15…

A:

Q: A steel rod of 2 cm diameter and 5 m long is subjected to an axial pull of 3000 kg. if E = 2.1 x 106…

A: Diameter d=2 cm Length L=5 m Axial pull P=3000 kg Elongation of rod=?

Q: The laboratory test results of standard proctor test are given in the tabl kimum dry unit weight of…

A: γwet=γbulk=wt of soilvolume of soilγdry=γd=wt of soil(1+moisture content)

Q: Q.3 Find the discharge in each pipe for below problems. Solve each questions up to three trials. hf…

A:

Q: Question A horizontal pipe of non uniform cross section has water flow through it such that the…

A:

Q: Complete the notes, find the elevation of point A and state the error in the network. Determine the…

A: HI= Elevation +BS Elevation= HI-FS

Q: 4. What are the major forest products that people use?

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…