Apply the boundary conditions and specified forces to your global stiffness system of equations and solve for the displacements. Consider the truss made of 2 bars with lengths 1 m, orientated in the structure shown in Figure 1. The two bars have the same cross-sectional areas A = 5·10-4 m² and modulus of elasticity E = 2·10¹¹ N/m². 10 kN is applied in the x-direction at node 1. A force of F1,x = 850 P 2 = 90° 2 AE L 1 1m 3 1m F1,x = 10KN Figure 1: Truss assembly formed of two bars. Nodes and bars are numbered, with bars numbered with underlines. X a) Using the numbering system of nodes and bars shown in Figure 1, state the 2 local stiffness matrices for each bar and combine these into a global stiffness system for all nodal displacements of the truss. Use the matrix system given in Eq. 1 below relating the local displacements of a single bar to the local forces applied to its nodes. fix fiy fjx fjy Here C = cos(0) and S = sin(0), where is the angle of orientation of the bar. CS -C² -CS C² CS S² -CS -S² -C² -CS C² -CS -S² CS CS S² R Wi Vi U j (1)

Apply the boundary conditions and specified forces to your global stiffness system of equations and solve for the displacements. Consider the truss made of 2 bars with lengths 1 m, orientated in the structure shown in Figure 1. The two bars have the same cross-sectional areas A = 5·10-4 m² and modulus of elasticity E = 2·10¹¹ N/m². 10 kN is applied in the x-direction at node 1. A force of F1,x = 850 P 2 = 90° 2 AE L 1 1m 3 1m F1,x = 10KN Figure 1: Truss assembly formed of two bars. Nodes and bars are numbered, with bars numbered with underlines. X a) Using the numbering system of nodes and bars shown in Figure 1, state the 2 local stiffness matrices for each bar and combine these into a global stiffness system for all nodal displacements of the truss. Use the matrix system given in Eq. 1 below relating the local displacements of a single bar to the local forces applied to its nodes. fix fiy fjx fjy Here C = cos(0) and S = sin(0), where is the angle of orientation of the bar. CS -C² -CS C² CS S² -CS -S² -C² -CS C² -CS -S² CS CS S² R Wi Vi U j (1)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.8P: The statically indeterminate structure shown in the figure consists of a horizontal rigid bar AB...

See similar textbooks

Similar questions

A bungee cord that behaves linearly elastically has an unstressed length L0= 760 mm and a stiffness k = 140 N/m. The cord is attached to two pegs, distance/? = 380 mm apart, and is pulled at its midpoint by a Force P = 80 N (see figure). (a) How much strain energy U is stored in the cord? (b) What is the displacement Scof the point where the load is applied? (c) Compare the strain energy (with the quantity PSC12. Note: The elongation of the cord is not small compared lo its original length.
A three-story steel column in a building supports roof and floor loads as shown in the figure. The story height H is 10.5 ft. the cross-sectional area A of the column is 15.5 in2, and the modulus of elasticity E of the steel is 30 × 106 psi. Calculate the strain energy U of the column assuming P1= 40 kips and P2= P3= 60 kips.
Wires B and C are attached to a support at the left-hand end and to a pin-supported rigid bar at the right-hand end (see figure). Each wire has cross-sectional area A =0.03 in2 and modulus of elasticity E = 30 X 106 psi. When the bar is in a vertical position, the length of each wire is L = 80 in. However, before being attached to the bar, the length of wire B was 79.98 in. and wire C was 79.95 in. Find the tensile forces TBand Tc in the wires under the action of a force P = 700 lb acting at the upper end of the bar.
By what distance h does the cage shown in the figure move downward when the weight W is placed inside it? (See the figure.) Consider only the effects of the stretching of the cable, which has axial rigidity EA = 10,700 kN. The pulley at A has a diameter da= 300 mm and the pulley at B has a diameter dB= 150 mm. Also, the distance L1= 4.6 m, the distance L2=10.5 m, and the weight W = 22 kN. Note: When calculating the length of the cable. include the parts of the cable that go around the pulley sat A and B.
A bar with a circular cross section having two different diameters d and 2d is shown in the figure. The length of each segment of the bar is L/2T and the modulus of elasticity of the material is E. (a) Obtain a formula for the strain energy U of the bar due to the load P. (b) Calculate the strain energy if the load P = 27 kN, the length L = 600 mm, the diameter d = 40 mm, and the material is brass with E = 105 GPa.
An aluminum bar subjected to tensile Forces P has a length L = 150 in. and cross-sectional area A = 2.0 in2 The stress-strain behavior of the aluminum may be represented approximately by the bilinear stress-strain diagram shown in the figure. Calculate the elongation S of the bar for each of the following axial loads: p = 8 kips, 16 kips. 24 kips, 32 kips, and 40 kips. From these results, plot a diagram of load P versus elongation S (load-displacement diagram).
A copper bar AB with a length 25 in. and diameter 2 in. is placed in position at room temperature with a gap of 0.008 in. between end A and a rigid restraint (see figure). The bar is supported at end B by an elastic spring with a spring constant k= 1.2 × 106 lb/in. (a) Calculate the axial compressive stress crcin the bar if the temperature of the bar only rises 50 F. (For copper, use a = 9.6 × 10-6/ and E = 16 × 106 psi.) (b) What is the force in the spring? (Neglect gravity effects.) (c) Repeat part (a) if k ? 8.
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
The statically indeterminate structure shown in the figure consists of a horizontal rigid bar AB supported by five equally spaced springs. Springs l, 2, and 3 have stiff nesses 3k, 5k. and k, respectively. When unstressed, the lower ends of all Five springs lie along: a horizontal line. Bar AB. which has weight W, causes the springs to elongate by an amount S. (a) Obtain a formula For the total strain energy of the springs in terms of the downward displacement d of the bar. (b) Obtain a formula for the displacement S by equating the strain energy of the springs to the work done by the weight W.
A uniform bar AB of weight W = 25 N is supported by two springs, as shown in the figure. The spring on the left has a stiffness k[= 300 N/m and natural length Lt=250 mm. The corresponding quantities for the spring on the right are k2= 400 N/m and L^ = 200 mm. The distance between the springs is L = 350 mm, and the spring on the right is suspended from a support that is a distance it = SO mm below the point of support for the spring on the left. Neglect the weight of the springs. (a) At what distance x from the left-hand spring (figure part a) should a load P = 18 N be placed in order to bring the bar to a horizontal position? (b) If P is now removed, what new value of k{is required so that the bar (figure part a) will hang in a horizontal position underweight If? (c) If P is removed and kt= 300 N/m. what distance b should spring ktbe moved to the right so that the bar (figure part a) will hang in a horizontal position under weight II"? (d) If the spring on the left is now replaced by two springs in series (kt= 300 N/m, kt) with overall natural length Lt= 250 mm (see figure part b). what value of k; is required so that the bar will hang in a horizontal position under weight IF?
-7 The truss A BC Shawn in the figure supports a horizontal load P1= 300 lb and a vertical load P2= 9001b. Both bars have a cross-sectional area A = 2.4 in2 and are made of steel with E = 30 X 106 psi. (a) Determine the strain energy U1of the truss when the load P1acts alone (P2= 0). (b) Determine the strain energy U2when the load P2acts alone (P1= 0). (c) Determine the strain energy U3when both loads act simultaneously.
A thin metal strip of total weight W and length L is placed across the top of a flat table of width L2as shown in the figure. What is the clearance S between the strip and the middle of the table? (The strip of metal has flexural rigidity EI.)