Consider the vibration isolation problem from base excitation. Instead of modeling the isolator as a spring and damper placed parallel to each other, model the isolator using the standard linear model. k ∞∞∞∞∞∞∞∞∞0 m base k₁ motion Develop an expression for the displacement transmissibility of the isolator in terms of the normalized forcing frequency, damping ratio, and the ratio of the two spring constants: y = k₁/k Discuss the influence of the stiffness ratio on the performance of the isolator. For a damping ratio of 0.01 and stiffness ratio of 0.05, use the transmissibility curve to find the effective damping ratio of the isolator (this is equivalent to having a spring and damper in parallel). Can the equivalent damping ratio reproduce the transmissibility curve accurately? Discuss. Provide one specific application where it is necessary to use the standard linear model.

Consider the vibration isolation problem from base excitation. Instead of modeling the isolator as a spring and damper placed parallel to each other, model the isolator using the standard linear model. k ∞∞∞∞∞∞∞∞∞0 m base k₁ motion Develop an expression for the displacement transmissibility of the isolator in terms of the normalized forcing frequency, damping ratio, and the ratio of the two spring constants: y = k₁/k Discuss the influence of the stiffness ratio on the performance of the isolator. For a damping ratio of 0.01 and stiffness ratio of 0.05, use the transmissibility curve to find the effective damping ratio of the isolator (this is equivalent to having a spring and damper in parallel). Can the equivalent damping ratio reproduce the transmissibility curve accurately? Discuss. Provide one specific application where it is necessary to use the standard linear model.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the vibrating system below: K4 Y(t) =Ysin30t where for = 30 and Y=20mm Find the following K1 K2 m C3 H C2 C1 C5 C4 1. Frequency Ratio 2. Displacement Transmissibility Ratio 3. Absolute displacement of the mass 4. Type of Damping 5. Equation of motion x(t). Assume Initial conditions for displacement and velocity 6. Graph 2 cycles of the vibrating system. You can use third party app for this. M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2=40 Ns/m C3= 35Ns/m C4= 15 Ns/m C5= 10 Ns/m
Given the vibrating system below: K1 K3 K4 Find the following 1. Keq 2. Ceq 3. Natural angular velocity K2 m C1 C3 C5 C2 C4 4. Damped angular velocity 5. Type of Damping 6. Equation of motion x(t). Assume Initial conditions for displacement and velocity Graph 2 cycles of the vibrating system. You can use third party app for this. 7. M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2= 40 Ns/m C3= 35Ns/m C4= 15 Ns/m C5= 10 Ns/m
you are given the mass, damping, andspring constants of an undriven spring-mass systemmy'' + μy + ky = 0.You are also given initial conditions. Use a numerical solverto(i) provide separate plots of the position versus time (y vs.t) and the velocity versus time (v vs. t),(ii) provide a combined plot of both position and velocity versus time, and(iii) provide a plot of the velocity versus position (v vs. y) inthe yv phase plane. a. m = 1 kg, μ = 0 kg/s, k = 9 kg/s2, y(0) = 3 m,y'(0) = 2 m/s b.m = 4 kg, μ = 4 kg/s, k = 1 kg/s2, y(0) = 3 m,y'(0) = 1 m/s
1) For the mass-damper system at right, the model in terms of velocity is mv + cv = f. The time constant of this first order system is t = m/c. For this system, a larger value of the damping constant c causes the time constant to decrease - which is counterintuitive. It seems that a small amount of damping should correspond to a system with a fast response. How can you reconcile this? m CA
Find the response of the mass if it is subject to the force in the plot. The damping ratio for the system is 0.1. You do not have to expand the series nor carry out any multiplication in the response equation. Hint: ao = 0. You may use this value and do not have to calculate ao- 2a 50 Mass m m = 10 kg Massless Rigid Rod a =0.3 m Massless Circular Cord -50 Length { = 0.625n m Diameter d = 0.01 m 0 1 Time (s) -2 -1 2 3 Modulus E = 0.001 GPa Force (N)
O choose 1/2 dynamics model or whole- car dynamic model of the automobile O obtaion the motion differential equations of the chosen model and the equations of non-damping free vibration O calculate the natural frequencies and natural modes by Matlab program 1/2 dynamic model of the automobile parameters O% body mass M 690kg O mass moment of inertia J, = 1222kgm O wheel mass M= 40.5kg. M= 45.4kg O tire stiffness k =k, - 192000N/m O sispension stiffness ky 17000N/m. k, =2000ONim O suspension damping coefficient c c, = 1500Ns/m O geometry dimensions a= 1.25m, b= 1.51m whole-car dynamic model of the automobile Xe kater el kel lee kal te parameters O body mass m,-1380kg O mass moment of inertia of pitch 1,-2444kgm O mass moment of inertia of roll 1,-3800kgm O Viwheel distance t-0.74m O the other parameters are the same as the l/2 dynamic model
A rigid rod with inertia (J) and length L is pinned at one end 0. A spring and viscous damper connected in parallel are fastened to the rod at a distance a from the support. The system is realsed with 0, = 2 and 6=0. Assuming that the damper is adjusted to provide a perfect underdamped damping ratio with undamped natural frequency of the system is 3 rad/s: 1. Calculate the angular displacement at 1= 1s after release. 2. If c= and a = k, compute the total enrgy equation and find the inital potentail energý 0 = f(t) www
The following model describes material model as a viscous damper in parallel with an elastic stiffness (spring) and both are in series with another spring. E E, C Drive the governing equation of the model (stress-strain relation) • Drive the creep behaviour of the model under constant load Drive the strass relaxation of the model under constant strain
For the system shown in Figure 2, u (t) and y (t) denote the absolute displacements of Building A and Building B, respectively. The two buildings are connected using a linear viscous damper with damping coefficient c. Due to construction activity, the floor mass of Building B was estimated that vibrates with harmonic displacement that is described by the following function: y(t) = y,cos (wt). k/2 Building A H k/2 M(t) C 73(1) Building B Equivalent (Building A) 00000000 Figure 2: Single-degree-of-freedom system in Problem 2. 111 uft) Please compute the following related to Building A: (a) Derive the equation of motion of the mass m. (b) Find the expression of the amplitude of the steady-state displacement of the mass m. (1) (Building B)
Shock absorber. What is the smallest value of the damping constant of a shock absorber in the suspen- sion of a wheel of a car (consisting of a spring and an absorber) that will provide (theoretically) an oscillation- free ride if the mass of the car is 2000 kg and the spring constant equals 4500 kg/sec²?
Problem 1: Laplace Transforms For a spring-mass-damper system with the following characteristics m = 70 k= 707 C = 69 Xo = 0 m/s Vo = 0 m/s If an forcing function F(t) = 100tet N is applied to the box at t = 0s, find x(t) for the system analytically. HINT: I STRONGLY suggest that you use the Laplace transform method. Please box your final x(t), and plot your solution.
For small positive damping, c, in the sinusoidally forced mass-spring system ma" + ca' + ka = Ggcos (wt) there is a value of the forcing frequency w for which the amplitude of the response is greatest - a resonance peak. very light darmping moderate damping very heavy darmping forcing frequency, w Derive a formula for the location of the peak in terms of the parameters in the differential equation (m, c, k; Go). So the location of the peak depends on the damping . Where does the peak move to as the damping constant c is reduced to zero? Does the above frequency have a name? amplitude of response