Consider you have to design a convertor to produce an output voltage of 36 V from a 3.3-V input DC source. The output current is 0.1 A. The design of above convertor should be for the output ripple voltage of 2 percent. The effect of ESR should be considered having relation to the capacitor value by as, r = 10-5/ Design the convertor subject to above mentioned design requirements and justify why a boost convertor will not be a good choice here.

Consider you have to design a convertor to produce an output voltage of 36 V from a 3.3-V input DC source. The output current is 0.1 A. The design of above convertor should be for the output ripple voltage of 2 percent. The effect of ESR should be considered having relation to the capacitor value by as, r = 10-5/ Design the convertor subject to above mentioned design requirements and justify why a boost convertor will not be a good choice here.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a buck converter such that the output voltage is 28V when the input is 48V. The load is 8Ohm. Design the converter such that it will be in continuous current mode. The output voltage ripple must not be more than 0.5%. Specify the frequency and the values of each component. Suggest the power switch also
100 W at 60 V from a Specify the 2 percent. size. Design a buck-boost converter to supply a load of 30 V source. The output ripple must be no more than duty ratio, switching frequency, inductor size, and capacitor
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
I need answer in your hand Design a buck-boost converter to supply a load of 100 W at 60 V from a 30 V source. The output ripple must be no more than 2 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
Question 4. Design a C converter by drawing according to the values given below.The C ´uk converter has 24 V input and 36 V output providing 80 W load. In this case, choose Duty ratio, switching frequency, inductor dimensions so that the variation in inductor currents is not more than 5 percent of the average inductor current, output voltage fluctuation is less than 1 percent and voltage fluctuation at C1 is less than 5 percent.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
Problem #1 A de-de converter produces 5V output with 2% line regulation and zero load regulation. The output leads connected to the load have a resistance of 4x10-32. Determine the worst-case minimum and maximum expected voltage at the load terminals for operation over full allowed input voltage range and a load variation over a range of 10W to 100W.
Ques-. Full convertor..
Design a Simple DCAC Converter. Then take a screenshot of your schematic and the graph of Vin and Vout.
Design a differentiator using an op-amp. The output voltage should be a square wave with 5V(peak-to-peak) andthe input voltage should be a triangular wave with10V(peak-to-peak) (1ms).