Consider_an automated ink bottling plant where a conveyor belt carries the empty bottles. The bottle is detected by a sensor and the bottle is filled with ink by a filling spout. The system also contains an emergency button that stops the process whenever it is pushed. An alarm signal is generated when any of the following conditions occur: • If there is no bottle on the conveyor belt and there is not plenty of ink in the tank at the same time If the emergency button is pushed Generate a truth table for this system. There will be three inputs (emergency (E), ink (I), bottle (B)) and one output (alarm signal, A) in the table Generate the Karnaugh map for the truth table. Draw the corresponding logic circuit using NAND gates only.

Consider_an automated ink bottling plant where a conveyor belt carries the empty bottles. The bottle is detected by a sensor and the bottle is filled with ink by a filling spout. The system also contains an emergency button that stops the process whenever it is pushed. An alarm signal is generated when any of the following conditions occur: • If there is no bottle on the conveyor belt and there is not plenty of ink in the tank at the same time If the emergency button is pushed Generate a truth table for this system. There will be three inputs (emergency (E), ink (I), bottle (B)) and one output (alarm signal, A) in the table Generate the Karnaugh map for the truth table. Draw the corresponding logic circuit using NAND gates only.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?
3) 94 select the proper answer for the following: 1) The main processes that have the responsibility of arc initiation in the switching of the high voltage power system are: a) the field and thermal emissions b) the deionization of the arc path c) the photoionization and magnetic field emission 2) The dead tank term is used with: a) Bulk oil circuit breaker b) Minimum oil circuit breaker c) Air blast circuit breaker 3) The errors in the PTs can be minimized by: a) By providing a suitable turn ratio b) By increasing the winding resistance and reactance 2
Q.1) Assume that the control of a bottle filling system is performed with an 8051 microcontroller. • The start and stop of the conveyor is controlled by the P1.0 pin. • The bottles are moving on the conveyor and detected with a sensor. When they arrive at the filling place, they are detected with a logical "1" signal, otherwise they are detected with a "0" signal. • A valve connected to P1.1 turns on for 10 seconds to fill each bottle. • At every X bottles, the conveyor will stop for 8 minutes and then start again. The remaining time to restart in the waiting period is displayed in minutes on the 7-segment display. • Logic "1" is detected from P1.3 during the operation of the system. Logic '0' is detected from P1.3 at the end of the shift. • At the end of the shift, the number of the filled bottles will be determined and saved in a memory location as 2 bytes. Write the required program. (Crystal Frequency:12MHZ). NOTE: X number will be taken as the last 2 digits of 59
(c) Sketch a complete flow chart of digital clock circuit by using the terms listed in Figure Q3(c). Display on LCD Sec. Display Min. Display Hour Display & Alarm Figure Q3(c)
Please answer with complete information. Thank you Explain the operation of squelch circuits
Which of the following is not a type of energy requiring lockout or tagout procedures? a. Pneumatic b. Hydraulic c. Kinetic d. Electrical
Magnetic Tape Recording Explain briefly the mechanism of Magnetic Tape Recording and how is induced electromagnetism applied in such. Magnetic Levitation (MagLev) Traing Explain briefly the mechanism of Magnetic Levitation (MagLev) Train and how is induced electromagnetism applied in such. Ground Fault Interrupter Explain briefly the mechanism of Ground Fault Interrupter and how is Faraday’s Law applied in such. Induction Stove Explain briefly the mechanism of Induction Stove and how is Faraday’s Law applied in such. Explain short and concise. Thank you.
H.W: Write a program to implement the process illustrated in figure below. The sequence of operating is to be as follows: • Normally open start and normally closed stop pushbuttons are used to start and stop the process. • When the start button is pressed, solenoid A energized to start filling the tank. • As the tank fills, the empty level sensor switch closes. • When the tank is full, the full level sensor switch closes. Solenoid A is de-energized. • The agitate motor starts automatically and runs for 3 min to mix the liquid. • When the agitate motor stops, solenoid B is energized to empty the tank. • When the tank is completely empty, the empty sensor switch opens to de-energized solenoid B. . The start button is pressed to repeat the sequence. SOL A Empty sensor switch Motor -SOL B Start/stop control station Full sensor switch
2. How does the magnetic blood flow meter work? Explain briefly.
Design a ladder program to run the material mixing system according to the following information: 1- When the start push button I0.0 is pressed, the pump (PUMP1 Q0.0) works for five seconds and then stops. 2- After that, the pump (PUMP2 Q0.1) runs for three seconds and then stops. 3- After that the pump (Mixer Motor Q0.2) works for 60 sec and then stops. 4- After that, the control valve (drian valve Q0.3) is opened, the pump (PUMP3 Q0.4) works for ten seconds. 5- The stop push button I0.1 is used to stop the system.
Flammable liquid is being pumped out of a steel drum into a steel bucket using a hand pump. Describe an appropriate grounding and bonding procedure. Please include a schematic of the proposed grounding and bonding arrangement.
Which one of the following devices can be used to accurately and conveniently measure the speed of amotor with a small slip?A. TachometerB. Revolution counter and stop watchC. Incandescent lamp and colored diskD. Stroboscope Note: I have doubts if it is the letter A or the letter D, can you help me in this question, thanks.