As a torque activity, your Physics TA sets up the arrangement shown below.m1m2A uniform rod of mass m,251 g and m2163 g and length L100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r,10.0 cm and r,90.0 cm mark, passed over pulleys, and masses of187 g are attached. Your TA asks you to determine the following.(a) The position r, on the rod where you would suspend a mass m, = 200 g in order to balance the rod and keep it horizontal if released from a horizontal position. In addition, for this case, what force (magnitude and direction)does the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the direction of the force the pin exerts on the rod as the angle 0-, measured with respect tothe positive x-axis (counterclockwise is positive and clockwise is negative).r3m%|F.N(b) Let's now remove the mass m, and determine the new mass m, you would need to suspend from the rod at the positionra= 20.0 cm in order to balance the rod and keep it horizontal if released from a horizontal position. In4addition, for this case, what force (magnitude and direction) does the pin exert on the rod? Express the direction of the force the pin exerts on the rod as the angle 0=, measured with respect to the positive x-axis(counterclockwise is positive and clockwise is negative).mAkgFpN(c) Let's now remove the mass mand determine the mass m, you would suspend from the rod in order to have a situation such that the pin does not exert a force on the rod and the location r- from which you would suspend4this mass in order to balance the rod and keep it horizontal if released from a horizontal position.m5kgr5

Givenuniform rod mass mr=163glength of the rod L=100cmmass m1=251gmass m1 distance from pin,…

d of mass m, = 163 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r,= 10.0 c and m2 = 187 g are attached. Your TA asks you to determine the following. he position r3 on the rod where you would suspend a mass m, = 200 g in order to balance the rod and keep it horizontal if released from a the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the directio ositive x-axis (counterclockwise is positive and clockwise is negative).

d of mass m, = 163 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r,= 10.0 c and m2 = 187 g are attached. Your TA asks you to determine the following. he position r3 on the rod where you would suspend a mass m, = 200 g in order to balance the rod and keep it horizontal if released from a the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the directio ositive x-axis (counterclockwise is positive and clockwise is negative).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

novable pulleys S0 the mechanical aduxintage is 3 b. The input force. Mechanical aduentage=load Couttput) Eprtcinput) Iaput R300 kq ż 3 - (00 EOutput mechanical adandaye Identify the following systems shown below: Picture Answer Picture Answer 1. 2. 3. 4. 5. 6. Input Force?
A shaft is supported by two bearings placed1.2 m apart. A pulley of diameter Dc=0. 675 meter is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25 kN. Another pulley of diameter Dd= 0.575 meteris placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt, which is placed horizontally to the right. The angle of contact for both the pulleys is 180° and u = 0.24. Determine the suitable diameter for a solid shaft, allowing working stress of 63 MPa in tension and 42 MPa in shearfor the material of shaft. Assume that the torque on one pulley is equal to that on the other pulley C A De m B Da m 0.3 m 0.2 m 1.2 m.
A 25-hp. 1750-rpm electric motor drives a machine through a multiple V-belt. The size 5V belts has unit weight of 0.012 lbf/in.) The pulley on the motor shaft has a 3.7-in. pitch diameter and geometry is such that the angle of wrap, o is 165º. k is consenvatively assumed that the maximum belt tension (F1) should be limited to 150 lbf, and that the coefficient of friction will be at least 0.512. [Hints: Use equations 17.18, 17.21, (h)]
Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
8. A Hooke's joint connects two shafts whose axes intersect at 150°. The driving shaft rotates uni- formly at 120 r.p.m. The driven shaft operates against a steady torque of 150 N-m and carries a flywheel whose mass is 45 kg and radius of gyration 150 mm. Find the maximum torque which will be exerted by the driving shaft. [Ans. 187 N-m] mum
A helical compression spring having 14 active coils is close coiled. It has a spring stiffness of 400lb/in. It is cut into two springs having 6 and 8 turns. Determine the spring stiffnesses of resulting springs.
3. A motor is connected by a belt to pulley B. T, is the tight-side tensile force equal to 1800 N. The shaft spins at a constant speed, 650 rpm. The power delivered by the motor is 12.6 kW. On pulley A, connected to the load, the slack side of the belt has a tension equal to th of the tight side. b T T, B d shaft Dimensions are as follows: da 200 тm 300 тт | 250 тm |180 тm | 250 тm 26 тm dB dahaft a We analyzed a problem similar to this on Test 01 using static failure theories. Is this strictly correct? Because the shaft is spinning, would not a material particle see a time-varying reversal of the the bending stress as in the R.R. rotating beam test? Would a particle see a reversal of the torsional shear stress? Assume Sut = 370 MPa and Sy = 300 MPa. Ignore Marin factors. Ignore stress concentrations. Ignore direct shear stress (that due to V). Find the safety factors with respect to fatigue and yielding. Be guided by section 6-14 on combined loading.
Q2 / A shaft transmitting 15kW at 200r.p.m. are supported by two bearings placed 1 m apart. A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25kN. Another pulley 400 mm diameter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt having maximum tension of 3.376kN, which is placed horizontally to the right. The angle of contact for both the pulleys is180° and =0.24. Determine the suitable diameter for a solid shaft if the bending moment acting on the shaft is reversed, allowing working stress of 42MPA in shear for the material of shaft and have yield stress of 400MPA and ultimate stress of 500MP.. And design the keys which support each pulley if the material of the keys is the same for the material of shaft.
Turning moment 1mm = 60NM: crank angle, 1 mm = 1°. The turning moment shows the maximum energy that needs to be stored by the flywheel in unit area is 2850 m?. The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m3. Reply.
A 2 hp, 2500 rpm electric motor drives a machine through a flat belt. The driven shaft speed requirement equals 1000 rpm. Find a. The pitch line velocity b. The radius of the driven pulley r2 and the angle o wrap of the driving pulley c. The values of tension forces Fl and F2 Given: c- 25 in., rl - 1.5 in.,f-0.35, w=0.01 Ib/in.
For nos. 21-23, satisfy the conditions of the given problem below: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear as shown in the figure 1. Determine: 21. the force in the strut AB. * 1 point 30° 450 lb. 1350 lb O A. 215.3 lb B. 224.4 lb C. 233. 2 lb D. 234.3 lb 1 ft 2 ft
The mechanism of four rods (Rocker Crank) as shown in the picture below is O₂A = 15 cm long, AB = 40 cm, BD = 10 cm, O2O4 = 45 cm, and O4B = 30 cm. Bar 4 receives a force Q of 4000 N. Determine the magnitude and direction of the torque in rod 2.