Design Criteria: Structure: Beams and reinforced walls exposed to freezir Required Strength: 28 MPa Minimum form dimension: 0.3m Minimum space between rebars: 65mm Minimum cover over rebars: 50mm Standard deviation of compressive strength of 2. MPa is
Q: 18. Design a Steel Beam. L= 40', Fy = 50 ksi, Pa = 10 k, PL = 30 k. Look up moment equation because ...
A: Solution: Calculate the factored design load: Pu = 1.2 PD + 1.6 PL = 1.2(10) + 1.6 (30)=12+48=60 k...
Q: Does pace factor is accurate? What are some factors that are paces are not the same? How important i...
A: Pace factor is defined as the ratio of the measured distance in the number of paces made by an indiv...
Q: In many cases of heavily loaded girders, shear distress is observed near the
A: This question is related to the Prestressed Concrete Structure From Design concrete structure.
Q: 1 The tolerance, tol, of the solution in the bisection method is given by tol = (b,-4.), where a, an...
A:
Q: 10mm 203mm 10mm BI 15 KN/M To D L/3 L/3 L/3 14mm 10000mm 94.5mm. 94.5m Girder ABCD Cross Section 274...
A:
Q: The safe stress , for a hollow steel column which carries an axial load of 2.1 x 10^3 kN is 25 MN/m^...
A: Given data- Axial load (L) = 2.1x 10^3 kN Safe stress(f) = 25 MN/m^2 External diameter (De) =25 cm =...
Q: At an average elevation of 855.50m the measured length of a baseline is 14,326.85m. Assuming that th...
A:
Q: A GPS satellite crossed your meridian today at 12:00 noon. When will it cross your meridian in the n...
A:
Q: d 1.59 m d = 5.22 feet Problem 8-12 0-mm-diameter concrete pipe is laid on a slope of 1 m per 500 m ...
A: To Determine From where sinθ is taken from, in the solution given.
Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength? A. O Pr...
A:
Q: The force in DB of the truss shown in below figure is W 5m 2W 5m W D O 5 W tension W tension 2 W com...
A: We have to determine the value of force in DB of the truss shown in above figure as per the given da...
Q: Situation2. Given: c&c, =W16x50: Ix=184in^4, C2, C3, Cg & Cg= W12x58: bx=475in^4, 91 = 92 = 93-W8x48...
A:
Q: What is zero tillage?
A: The mechanical manipulation of soil to produce the desired effect in which certain tools are used to...
Q: Given are the stations and elevations of a proposed symmetrical parabolic highway curve. POINT ELEVA...
A: We have to determine the value of length of the symmetrical curve and stationing and elevation of PC...
Q: A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear sp...
A:
Q: Plot the load-def lection diagram for apinned-end column with eccentric axial loads (seefigure) if t...
A: Given:- L = 3.6 m, I = 9.0 x106 mm4, E = 210 GPa. To find:- the load-def lection diagram
Q: E=200 x 10° N/m? A=300mm2 L=3m B. 3 m 4.5 m
A: E = Young's Modulus of Elasticity = 200 x 109 N/m2 A = Cross sectional Area = 300mm2 L = 3000mm
Q: Situation 6: A built-up beam is composed of the following: bf = 360mm tf = 28.0mm d = 600mm tw = 20 ...
A:
Q: What is the process of tunnelling? What are the three different types of tunnelling protocols
A: Step: 1 Tunnels are underground civil engineering structures which give passageway and surrou...
Q: s. The column is restrained on both ends. Fy = 248 MPa
A: load =P = 1000×103N A = 36770 mm2C = 0.85IX = 50364×106mm4Iy = 156.09×106 mm4 since ecentricity alon...
Q: For the system forces shown, solve the following: (the coordinates are in meters) y 75 kN 100° (4, 1...
A:
Q: Problem 1. Use virtual work method and determine the following unknowns on the frame shown below. Us...
A:
Q: A retaining wall 8 m high with a smooth vertical back retains a clay backfill with C = 15 kN/m2, 0 =...
A:
Q: The cross-sectional are of each member in cm2 is underlined. Each member is made of steel, E = 20 * ...
A: We have to determine the value of unknown nodal displacement and axial force in each member of the g...
Q: Degree of saturation is the ratio of volume of water in the voids to the *.volume of the voids True ...
A: Based on the 3 phase diagram of soil We have Total volume of soil (V) is equal to sum of Volume of ...
Q: of 2,00,000 litres of raw water, found to have the following chemical & Calculate the requirement of...
A:
Q: Problem: Replace the force system acting on the post by a resultant force, and specify where its lin...
A:
Q: A cast-iron beam carries the loads shown. If f < 20 MN/m? and f. < 80 MN/m? a. Compute the permissib...
A:
Q: A retaining wall 10 m high retains a cohesionless soil with an angle of internal friction 30°. The s...
A:
Q: A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is...
A: Given data- Discharge (Q)=12 lit/s=12×106 mm/sArea A=π4×d2=π4×1002=7853.98 mm2Pressure P=720 kPa=720...
Q: Magmas are developed when melting occurs either within or beneath the earth * .crust that is in the ...
A: Magma : 1. Magma is an extremely hot liquid and semi-liquid rock located under Earth’s surface. 2. W...
Q: 5. If exactly 20 bolts of 2.5cm diameter are needed to hold an air chamber together at A-A as a resu...
A:
Q: Without using an instrument, how can you determine if a soil has the proper moisture content for dry...
A: Water content or moisture content is the quantity of water contained in a material, such as soil (ca...
Q: D 4 3
A:
Q: o. A rectangular sedimentation tank following coagulation- Exa flocculation is to treat a flow of 30...
A:
Q: 10.19. The channel shown in Figure P10.19 has a symmetric cross section with left and right overbank...
A:
Q: Problem 4) (a) Use modal analysis to determine the following properties for the following idealized ...
A:
Q: Differentiate land preparation from tillage for farming?
A:
Q: he repair and rehabilit amaged or spalled co one emovina the by ro
A:
Q: in the jet and the discharge when h = 4.xy ng the liquid head h at 4.xy ft, and neglecti ntage by wh...
A: Q = discharge in orifice = Ca2ghQ = 0.95×π5422×g×4×13g= 9.8m/s2g =385.82 in/s2Q=0.95×π4422×385.82×4×...
Q: Azimuth (N) Observation Distance (m) 231.56 AB 176°47'15" ВС 137.98 203°23'23"
A:
Q: The back tangent of a simple curve has an azimuth of 180֯and the forward tangent has an azimuth of 2...
A: Given- Back tangent azimuth = 180֯ forward tangent azimuth = 230֯ The degree of the curve (arc basis...
Q: If the compressive strength is 30.68 MPa, water - cement ratio is 0.45, and coarse aggregate is 992 ...
A: Given, Compressive strength = 30.68 MPa w/c ratio = 0.45 Coarse aggregate = 992 kg/m3
Q: A 15 cm diameter pipe carries a flow of 70 litres per second of an oil (sp.gr = 0.75). At a section ...
A:
Q: A flat bar of a width b = 60 mm and thicknesst = 10 mm is loaded in tension by a force P (seefigure)...
A: (a) Determine the pin diameter dmforwhich the load P is a maximum.(b)Determine the value of maximum ...
Q: 1. Solve the slope and deflection for the problem using Double Integration. Box the Moment Curvature...
A:
Q: A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN. The steel ...
A: A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN.The steel s...
Q: Given the following information for a simple spiraled curve: o | = 38°00'00" Da = 4°30'00" Ls = 800 ...
A: We have to determine the Y coordinate of S.C in feet assuming the T.S is the origin (0,0) as per the...
Q: Q4: - For the system as shown in Figure (2), By Engineering Analysis and 1" O.D.Eq. Find the quantit...
A: Adult should eat no more than 6g of salt a day (2.4g sodium)-that's around 1 teaspoon. Children aged...
Q: Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of dia...
A:
Determine the Moist fine aggregate, in kg/m3 and Moist coarse aggregate, in kg/m3. with solution
Step by step
Solved in 3 steps with 3 images
- 10. Design a concrete mix for the following conditions and constraints using the absolute volume method Design Environment Bridge pier exposed to freezing and subjected to deicing chemicals Required design = 25.1 MPa Minimum dimension = 0.4 m Minimum space between rebars = 60 mm Minimum cover over rebars = 50 mm Standard deviation of compressive strength of 2.8 MPa is expected (more than 30 samples) Only air entrainer is allowed Available Materials Cement Select Type V due to exposure Air Entrainer Manufacturer specification 6.2 ml/1% air/100 kg cement Coarse aggregate 25 mm maximum size, river gravel (round) Bulk oven dry specific gravity = 2.621, Absorption = 0.4% Oven dry-rodded density = 1650 kg/m3 Moisture content = 1.4% Fine aggregate Natural sand Bulk oven-dry specific gravity = 2.576, Absorption = 0.7% Moisture content = 3% Fineness modulus = 2.50Design the concrete mix according to the following conditions:Design EnvironmentBuilding frameRequired design strength = 27.6 MPaMinimum dimension = 150 mmMinimum space between rebar = 40 mmMinimum cover over rebar = 40 mmStatistical data indicate a standard deviation of compressive strength of2.1 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification 6.3 mL/1% air/100 kg cement.Coarse aggregate: 19 mm nominal maximum size, river gravel (rounded)Bulk oven-dry specific gravity = 2.55, absorption = 3.6,Oven-dry rodded density = 1761 kg/m3Moisture content = 2.5,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.659, absorption = 0.5,Moisture content = 2,Fineness modulus = 2.47Design the concrete mix according to the following conditions:Design EnvironmentPavement slab, Bozeman, Montana (cold climate)Required design strength = 3000 psiSlab thickness = 12 in.Statistical data indicate a standard deviation of compressive strength of250 psi is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification is 0.15 fl oz/1% air/100 lb cement.Coarse aggregate: 2 in. nominal maximum size, crushed stoneBulk oven-dry specific gravity = 2.573, absorption = 2.8,Oven-dry rodded density = 120 pcfMoisture content = 1,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.540, absorption = 3.4,Moisture content = 4.5,Fineness modulus = 2.68
- Q3: B: Design the concrete mix according to the following conditions: Design Environment Building frame Required design strength = 27.6 MPa Minimum dimension = 150 mm Minimum space between rebar = 40 mm Minimum cover over rebar = 40 mm Statistical data indicate a standard deviation of compressive strength of 2.1 MPa is expected (more than 30 samples). Only air entrainer is allowed. Available Materials Air entrainer: Manufacture specification 6.3 ml/1% air/100 kg cement. Coarse aggregate: 19 mm nominal maximum size, river gravel (rounded) Bulk oven-dry specific gravity = 2.55, absorption = 3.6, Oven-dry rodded density = 1761 kg/m3 %3D Moisture content = 2.5, Fine aggregate: Natural sand Bulk oven-dry specific gravity 2.659, absorption=0.5, Moisture content = 2, Fineness modulus = 2.47Design the concrete mix according to the following conditions: Design Environment Building frame Required design strength = 27.6 MPa Minimum dimension = 150 mm Minimum space between rebar = 40 mm Minimum cover over rebar = 40 mm Statistical data indicate a standard deviation of compressive strength of 2.1 MPa is expected (more than 30 samples). Only air entrainer is allowed. Available Materials Air entrainer: Manufacture specification 6.3 ml/1% air/100 kg cement. Coarse aggregate: 19 mm nominal maximum size, river gravel (rounded) Bulk oven-dry specific gravity = 2.55, Absorption = 0.3% Oven-dry rodded density = 1761 kg/m3 Moisture content = 2% Fineness modulus = 2.47Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table.a) Required…
- Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table d) The amount…Design a concrete mix for the following conditions and constraints using the abso- lute volume method: Design Environment Bridge pier exposed to freezing and subjected to deicing chemicals Required design strength = 24.1 MPa Minimum dimension = 0.3 m Minimum space between rebars = 64 mm Minimum cover over rebars = 64 mm Standard deviation of compressive strength of 2.4 MPa is expected (more than 30 samples) Only air entrainer is allowed Available Materials Cement Select Type V due to exposure Air Entrainer Manufacturer specification 6.3 mL/1% air/100 kg cement Coarse aggregate 25 mm nominal maximum size, river gravel (round) Bulk oven dry specific gravity = 2.621, absorption = 2.4% Oven dry-rodded density = 1681 kg/m³ Moisture content = 1.5% Fine aggregate Natural sand Bulk oven-dry specific gravity = 2.572, absorption = 0.8% %3D Moisture content = 4% Fineness modulus = 2.60Design a concrete mix for the following conditions and constraints using the absolute volume method:Design EnvironmentBuilding frameRequired design strength = 27.6 MPaMinimum dimension = 150 mmMinimum space between rebars = 40 mmMinimum cover over rebars = 40 mmStatistical data indicate a standard deviation of compressive strength of 2.1 MPa is expected (more than 30 samples)Only air entrainer is allowedAvailable MaterialsAir EntrainerManufacturer specification 6.3 ml/1% air / 100 kg cementCoarse aggregate19 mm nominal maximum size, river gravel (rounded)Bulk oven dry specific gravity = 2.55, Absorption = 0.3%Oven dry-rodded density = 1761 kg/m3Moisture content = 2.5%Fine aggregateNatural sandBulk oven-dry specific gravity = 2.659, Absorption = 0.5%Moisture content = 2%Fineness modulus = 2.47
- Design the concrete mix according to the following conditions:Design EnvironmentPavement slab, subjected to freezingRequired design strength = 21 MPaSlab thickness = 300 mmStatistical data indicate a standard deviation of compressive strength of1.7 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification is 9.5 mL/1% air/100 kgcement.Coarse aggregate: 2 in. nominal maximum size, crushed stoneBulk oven-dry specific gravity = 2.573, absorption = 2.8,Oven-dry rodded density = 1922 kg/m3Moisture content = 1,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.540, absorption = 3.4,Moisture content = 4.5,Fineness modulus = 2.68Design the concrete mix according to the following conditions:Design Environment• Concrete slabo Subjected to freeze and thaw.o Required design strength = 21 MPao Slab thickness = 300 mm.o Statistical data indicate a standard deviation of compressive strengthof 1.7 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Available Materials:o Air entrainer:▪ Manufacture specification is 9.5 mL/1% air/100 kg cement.o Coarse aggregate:▪ 25 mm nominal maximum size▪ Crushed stone▪ Bulk oven-dry specific gravity = 2.573▪ Absorption = 2.8▪ Oven-dry rodded density = 1922 kg/m3▪ Moisture content = 1o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.540▪ Absorption = 3.4▪ Moisture content = 4.5▪ Fineness modulus = 2.60o Cement:▪ Type I Cement▪ Specific gravity = 3.15…Design a concrete mix for the following conditions and constraints using absolute volume method. Design Criteria: Structure: Beams and reinforced walls exposed to freezing and Thawing Required Strength: 28 MPa Minimum form dimension: 0.3m Minimum space between rebars: 65mm Minimum cover over rebars: 50mm Standard deviation of compressive strength of 2. MPa is expected (more than 30 samples) Classification: air entrained, mild exposure, Use exact value from table, use 75mm slump Material classification: Cement: Cement type II Air entrainer: 5 ml/1% air/100kg cement Coarse aggregate: Nominal maximum size: 19mm Type: river source, gravel with crushed particles Bulk oven dried specific gravity: 2.60 Absorption: 0.4% Oven-dried rodded density: 1600 kg/m3 Moisture content: 2% Fine aggregate: Type: natural sand Bulk oven dried specific gravity: 2.55 Absorption: 0.8% Fineness Modulus: 2.80 Moisture content: 3% Determine: Air content, in percent - Water content, kg/m³ – Cement, in kg/m³ -…