Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of the 50° support surface at C. The forces are positive if in tension, negative if in compression. A 195 lb 5.5' B 2.0⁰ 50°

Q: Who is ultimately responsible for the welder’s safety?

A: Welding is a process in which a large amount of the gasses and heat released if all these are not…

Q: Example : Pump flow = 1.5 M3/hour (max flow) Product density = 1.2 gram/ml Production…

A: Please refer to the detailed solution given below, Answer - 1) Q = 0.25 m3/hour 2) Given pump is…

Q: How do excessive amounts of manganese affect a weld?

A: The fabrication process is the process which is involved to build a product by mixing standardized…

Q: 2. Steam at 6.2 Mpa and 480°C is received by a regenerative engine. Extractions for feedwater…

A: Introduction: Because of irreversibilities in many components, the real vapor power cycle differs…

Q: A bench blast has the following drill hole parameters, diameter 200mm, bench height 10m, stemming…

A:

Q: When a flat plate is subjected to uniform heat flux, how different are the relations compared to the…

A: The Nusselt number will be different for each different case depending on the nature of the flow…

Q: Find the sum of the forces F1, F2 =196 N, and F3, if 0 = 60

A:

Q: An engine attains a velocity of 30 km/h in 2 min from rest in a train of 200 KN weight on a level…

A: Given Data The velocity attains by the engine is: V=30 km/h=8.33 m/s The time taken by the engine…

Q: Find displacement Work done=1111 J Force 111 N

A: Given data : Force F=111 N Work done W=1111 J   Required : Displacement

Q: A compression-ignition engine with compression ratio of (1.50x10^1) is being designed. Pressure and…

A:

Q: 300 kJ of thermal energy is stored at a temperature of 1000 K. Assuming perfect heat transfer to a…

A:

Q: A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C…

A:

Q: A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It…

A: Given dataP=3MPaT=600°CQ=10MWPs=500kPaTs=45°C Here we using the steam table with respect to the…

Q: Using W760X134 as the section for the beam, determine the value (kN) of the nominal collapse load…

A:

Q: hy isn't anyone answering this?? A 50 lb block drops onto the top of a 25 lb spring scale. The block…

A: Given:m=50 lbms=25 lbh=6 ft =72 ink=100 lb/in

Q: What work holding device that is used for face milling and peripheral mill, why so? Subject:…

A: Face milling is a machining process in which the milling cutting is placed perpendicular to the…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: The signboard truss is designed to support a horizontal wind load of 560 lb. If the resultant of…

A: Draw the free-body diagram of the signboard truss.

Q: 1.52 Given that P - 120 lb and Q - 130 lb, find the rectangular representation of P+ Q. 12 Figure…

A:

Q: Supply air at 18°C dry-bulb and RH of 80% flows through a duct whose inside wall temperature is…

A:

Q: The two blocks shown are originally at rest. Block A has a weight of 100 lb and block B has a weight…

A: Given:WA=100 lbWB=250 lb

Q: Do you think that the shockwave occurs in this bullet travel for both medium of gas? Sketch your…

A: Given data:   Speed of bullet = 1548 miles per hour = 692.0179 m/s The properties of the two mediums…

Q: A skydiver jumps from (5.000x10^3) m with no parachute into a giant net. The mass of the skydiver is…

A: Given data: Mass of skydiver = m = 1.05 x 102 kg = 105 kg Projected Area = A = 0.45 m2 Pressure = P…

Q: The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker…

A:

Q: 1200 N 800 N 400 N D 2 m B A K J 2 m E 2 m 2 m G 2 m H Using Method of Sections (one cutting section…

A:

Q: A fluid is pumped at a rate of 0.00156 m³/s through a 0.025-m-diameter pipe to fill a water tank as…

A:

Q: A Hexagonal pyramid of base side 30 mm and axis 60 mm is on a triangular face in the HP 21. with its…

A:

Q: In a steady state process mass flow rate is equal to the product of cross-sectional area and…

A: Given Statement:- In a steady state process mass flow rate is equal to the product of…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: first image is blur but second image is clear. so I am solving second image question. Kindly repost…

Q: As illustrated in Figure 1, the rectangular bar with dimensions of 250 mm by 400 mm is subjected to…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 675 lb, a = 2.7 ft, b = 2.0 ft, r = 9 in.…

A:

Q: What is the lowest acceptable amperage setting for GTAwelding?

A: Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding…

Q: Knowing that a 0.02in gap exists when the temperature is 75'F, determine (a) the temperature at…

A:

Q: Find the force CD. The force is positive if in tension, negative if in compression.

A:

Q: plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the…

A: Given:P1=3 MPaT1=600°CTc=45°CP2=500 KPa

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

A:

Q: A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn…

A: Given Data : Clicking Noise  Transmission operation

Q: Two steel springs with plain ends are arranged in series and supports a load. The upper spring has…

A:

Q: Compute the Strain if change in length is 0.0456 mm and original length of rod is 8 mm

A: Given data : Change in length ∆L=0.0456 mm Original length L=8 mm   Required : Strain

Q: A four-cylinder, two-stroke 2.4-L diesel engine that operates on an ideal Diesel cycle has a…

A:

Q: Three identical circular disks A, B and C are welded to the ends of three identical solid circular…

A: Please refer to the detailed solution given below, Answer maximum shear stress developed is 48.01…

Q: To make truss stable how many member are required Support reaction=4 Joint=7

A:

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A:

Q: ocal hea

A: Local heat transfer coefficient will be at the particular on heat transfer surface it is equal to…

Q: The products of combustion flow inside the exhaust ducts at the rate of 3.4 kmol/s. The products of…

A:

Q: AF 8.5 lb force is applied to the handles of the vise grip (Eigure Figure Part A 0.75 in. 1 in. B…

A:

Q: Link 2 is isolated from a kinematic diagram and shown in Figure P7.16. The link is rotating counter-…

A: Given data: N=300 rpmγ=50°β=60° Need to determine the total linear acceleration of points A and B.

Q: Find displacement Work done=1111 J Force=111 N

A: The displacement is s = 10.009 m.

Q: Return air at 25°C and fresh outdoor air at 35°C is mixed in an adiabatic mixing chamber. If 22% of…

A: Temperature of returned air = 25 oC Temperature of outdoor air = 35 oC After mixing, 22% of the…

Q: The marketing research department of a large manufacturing company has determined that the demand…

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.