Determine the largest load P that can be applied to the frame without causing either the AVERAGE normal stress at member CB orthe average shear stress at pin B (double shear) to exceed a = 150 MPa and t = 60 MPa, respectively. Member CB has a squarecross section of 25 mm on each side. Pin B has a radius of 10 mm.75000 NB) 50625.3627NⒸ37699.1624 ND) 30159.2895 NE) 208332.3409 NF) 24657.3561 N2mBA1.5 ma

member CBaverage normal stress=150MPashear stress=60MPacrossection:square of 25mm side

Determine the largest load P that can be applied to the frame without causing either the AVERAGE normal stress at member CB or the average shear stress at pin B (double shear) to exceed o=150 MPa and t = 60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. Pin B has a radius of 10 mm. 2m www B A 1.5 m ***

Determine the largest load P that can be applied to the frame without causing either the AVERAGE normal stress at member CB or the average shear stress at pin B (double shear) to exceed o=150 MPa and t = 60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. Pin B has a radius of 10 mm. 2m www B A 1.5 m ***

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam has the cross section shown (thin-walled profile). The shear center is at a distance, e = 32.7 mm from the web, IEN = 1134000 mm4. If a force V = 30 kN is applied, passing through the shear center as shown, determine the nearest value of the shear stress in the web at C. |5 mm 3 mm 3 mm 30 mm D 80 mm 30 mm mm E F 55 mm а. 117 МPа O b. 70 MPa Ос. 138 МРа O d. 94 MPa
75MPA Q 1: A plane element is subject to the stresses. Determine analytically (a) the principal stresses and their directions and (b) the maximum shearing 62.5MPA SOMPA 50MPA 62.5MPA 75MPA
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear-stress components on a volume element located at this point. 200 mm 20 mm B 200 mm -20 mm 300 mm 20 mm
|y 1. Three forces are applied to the bar shown. Calculate principal stresses and maximum shearing stress at (a) point a, (b) point b, (c) point c. 48in 50 kips 0.9 in. 0.9 in. h = 10.5 in. 1.2 in. 1.2 in. 4.8 in. 2 kips C 2.4 in. 2 in. 6 kips 1.8 in du Z
Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the 3/4 in diameter pin is in double shear. ANS: P = 19770 lb-f A 10 in. B 30° P 12 in. C
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
The frame system is pin supported at A and B, and has an internal hinge at E as shown below, 1. Find the slope at Cusing the principle of virtual work, ignore axial and shear deformations 2. Find the slope at Cusing the principle of virtual work, consider axial and shear deformations, knowing that section-area of members AD and BF equals 22x10³ mm?, and the section-area of members CE and EG equals 26x10 mm? 15 kN/m G 21 D 21 E Hinge 21 F 21 3 m 65 I I kN 3 m BA -3 m- 5 m 5 m 2 m E = 200 GPa I = 350 (106) mm4
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
SOLVE STEP BY STEP IN DIGITAL FORMAT Determine by the method of nodes the forces at which the members EG, GF and FH, EF and ED of the following truss work. 4 kN 8 kN 2 m G 2m H. 8 kN 2m E 2m 8 kN 2m 2m 4 kN 2m 2m A B.
At a point 8ft from D, solve the shear stress 4in from the top of the cross-section. The cross section is 6in by 18in. 16 k 2 k/ft 8k 3 k/ft B -12 ft 8 ft-+9 ft- 12 ft +-9 ft- 4 ft 3 ft 3 ft O 16.46psi O 65.84psi O 8.23psi O 32.92psi
The truss shown in the figure has a uniform cross - sectional area of A and modulus elasticity E. 4. Taking member BD as the redundant member, which of the following most nearly gives the relative displacement of joint B and D when this member is removed. а. 114.05/АЕ b. 98.16/AE c. 81.21/AE d. 121.82/ AE 15 kN 5. Which of the following most nearly gives the stress in member BD a. 9.3 KN b. 8.4 KN 3 m c. 5.6 KN d. 11.4 KN 6. Which of the following most nearly gives the stress in member CD a. 9.05 KN b. 6.04 KN 3 m C. 13.4 KN d. 18.3 KN
A 7.5-kN force F is applied to the beam by means of a welded plate at A as shown. Using vector analysis determine the following prompts below: 0.58 m 28° F -5.3 m- The force vector F is represented by The j component of the position vector rA The Moment at point O :: 3.521i - 6.622j :: -6.622i + 3.521 j :: -0.29 :: -6.622 :: 5.31 :: -34.075 k :: -0.29i - 34.075k : -34.075 j - 34.075 k