(Show a Step-by-step Solution with description for every step) 10. Determine the maximum safe wind load wW (kN/m) on the rafter shown based on apositive moment capacity of 170 kN-m and negative moment capacity of 320 kN-m. ofthe rafter. Use the load combination 1.2D + 1.0W.WDL = 35 kN/mWD1.2mBA8.7mU3.1m4.6m

Answered: Image /qna-images/answer/84c82343-a031-46f1-93e7-7d042e24c12c.jpg

Answered: Determine the maximum safe wind load wW…

Determine the maximum safe wind load wW (KN/1 n) on positive moment capacity of 170 kN-m and negative moment capacity of 32 the rafter. Use the load combination 1.2D + 1.0W. WDL = 35 kN/m W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the value of friction if normal force is 1200 N and coefficient of friction is 0.462

A: Given data : The value of coefficient of friction μ=0.462 The value of normal force N'=1200 N To…

Q: Calculate static indeterminacy of truss

Q: The following results are obtained from a series of cone penetrometer tests. Mass of empty can, g…

Q: Problem 02. The fixed supported frame below carried a uniformly distributed load of 30KN/m along…

Q: Given data : Depth of flow=2 m Velocity of flow=3 m/s g=10 m/s2 Find specific energy

Q: 9 A high tension cable 5 cm in diameter is strung- out between two towers. At a wind velocity of…

Q: soil sample has a unit weight of 1.9 g/cc and w=12%. If Gs of solids is 2.65, determine the volume…

Q: A pentagon-shaped saddle containing four rain-gauging stations. The coordinates of each of the five…

A: given that,

Q: 8.63 Two reservoir maintain a constant difference of water levels of 11.25 m and are connected by a…

A: Given data, Here the value of V ( flow velocity through pipe ) is unknown. To find the value of V…

Q: (a) how that the polar radius of gyration ko of the annular area shown is approximately equal to the…

Q: A prestressed concrete beam 223mm x 677mm has the following service loadings PDL=67 KN PLL=44 KN…

Q: A solid circular concrete pile is to be driven into a clayey soil with the following properties:…

A: Cu1 = 40 kPa Length (L1) = 5 m unit weight (γ1) = 15 kN/m3 Cu2 = 50 kPa Length (L2) = 10 m unit…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 1 6 mm A 150 mm 6…

Q: What is a rule of thumb?

A: A rule of thumb is a general or approximate way of doing something that is based upon common…

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

Q: 454 For Problems 20.17 through 20.20, use the matrix approach to solve fo the member end forces. In…

Q: 0 (115) Now 20kip D MB = -2835.67 kipft чок р Hinge З кір JE UNDO, CLAPEP SP с 50kip 20 кір B 264.3…

Q: Need asap. Please input the right formulation and solution. Provide explanation thank you. Answer on…

Q: 95 rate/minute, 7200 seconds, and 0.10m diameter are provided. compute the velocity using the…

Q: ing Problem ean sheet . Draw the shear and bending moment Diagram of the following A) 71kN/m A B 8 m…

Q: 15kN A 2m 3m 25kN/m 5m 14m 4m QUE

A: Given data:

Q: During a flood flow the depth of water in a 12 m wide rectangular channel was found to be 3.5 m and…

Q: A tractor weighing 3000lb, with a wheel base of 9ft, carries 1800lb of its load on the rear wheels.…

Q: a consolidated tri-axial test was conducted on a normally consolidated clay. the results were as…

A: Given: The chamber confining pressure is 316 kPa. The deviator stress is 424 kPa.

Q: In a triaxial test for a cohesive soil sample, when the principal stresses are 483.36 kPa and 60.39…

Q: In triangle ABC, b = 17, c = 22, and A = 143°. Find B. O 14 O 17 O 20 O 16 O Other:

A: We will apply cosine formula.

Q: Calculate the circumferential stress of a thin walled spherical shell of a diameter 220 mm and the…

Q: Determine the value of coefficient of active pressure of soil having angle of internal friction 33…

A: Given data : The value of angle of internal friction= ϕ ϕ=33∘ Required: Coefficient of active…

Q: Why does the estimate of probable total cost need to be revised as the project progresses?

A: there are two reasons for revise cost of project as project progress.

Q: The soil arrangement shown carries 1.88-meter square footing with a column load of 596 kN.…

Q: SITUATION. A truss is loaded and supported as shown below. It is carrying a vertical point load at…

Q: determine the maximum flow rate

A: * Triangular Channel: - It is defined as an open channel whose cross section is like triangle where…

Q: Answers: 0x = Txy Op2 = i i i MPa MPa MPa

Q: A pump is used to dewater construction sites. When deep foundations are being constructed the water…

A: Formulae used 1. Pressure = row × g ×h 2. Power = row × g × Q × H Where…

Q: statically determinate, or statically indeterminate. If the truss is statically indeterminate, then…

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest…

Q: At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 52 MP exist on…

A: To find unknown stresses

Q: A 12-meter-long beam is simply supported at the right end and at 2 meters from the left end. It is…

Q: 40 MPa 35 MPa 60 MPa

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. B TH 1 m-…

Q: c. Using water reducer, how can we improve workability without changing the compressive strength?…

A: Given data,

Q: If the free end of a cantilever of span / and flexure rigidity El undergoes a unit displacement…

Q: nd the value of strain if stre O MPa

Q: Calculate the side resistance in kips using the US Army Corps of Engineers (EM 1110-2-2906, Figure…

A: Given Data: Shear strength = 3752psf pile diameter = 14 in = 14/22ft = 1.167ft Length = 22ft

Q: Angela wants to determine the permeability of an aquifer. The aquifer has a test well 300-mm in…

A: The diameter of test well, d=300mmThe radius, r=d2=150mmThe radial distance of first observation…

Q: A helicopter is rising vertically from the ground at a constant rate of 4.5 meters per second. When…

Q: X A cylindrical part of diameter "d" is loaded in tension by a load "P" causing a stress: a-P/A. The…

A: Given, Uncertainty in load = ±15% Uncertainty in diameter = ±7.5% Uncertainty in stress = ±15%

Q: For a constant laboratory permeability test on a fine sand, the following data are given: Length of…

Q: n, g n+wet soil sample, g + dry soil sample, g mm 25 limit in percent. Round off to two decimal pla…

A: Cone penetration method Given two samples Draw the graph between moisture content and cine…

Q: Determine the forces in members BE and CE of the loaded truss

Q: A prestressed concrete pile, 482 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Concept explainers

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.

Question

100%

(Show a Step-by-step Solution with description for every step)

10. Determine the maximum safe wind load wW (kN/m) on the rafter shown based on a
positive moment capacity of 170 kN-m and negative moment capacity of 320 kN-m. of
the rafter. Use the load combination 1.2D + 1.0W.
WDL = 35 kN/m
W
D
1.2m
B
A
8.7m
U
3.1m
4.6m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

300(6) +70@ cos 30 (9) + 15 X = 7.36 m 2/86 If the resultant of the loads shown passes through point B, determine the equivalent force-couple system at 0. R= 45 kN 54 kN 1.2 m 0.9 m 0.9 m M 18 kN
A beam ABC with an overhang at one end supports a uniforms load of 12 kN/m and a concentrated load of 2.4 kN at the free end at C. A 1.60 m O Option 1 O 10.5 KN O 14.5 KN O 12 kN/m 7. Determine the maximum shear. 13.2 KN 7.26 KN 1.60 m th 2010 200 K-4 ** Lowa 52500 dal ilippipap adi Car *** *644 i Eddy lady ft Ripley day fild polyl pontedy jillet id iphondo ordin WE XPERT HUPI in want thing happy h tip licht und | filla popoliti i *** FR ****** chat puku pia jo y de plany hikme of billik) MASAT shndite tud A B 10300002 1.60 m SATAN the Karda Die ik jy diduduk y tế bào trung và mộ hry ripp wameta tal. poskyt 2005-0 2.4 KN C
Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN 0.8m A B H G 1.5 kN 4 - 1m panels = 4m F 1.5m M
A 1.6-m-long cantilever beam supports a concentrated load of P = 7.2 kN. The beam is made of a rectangular timber having a width of 120 mm and a depth of 280 mm. Calculate the shear stress due to the applied load at a point located d = 76 mm below the top surface of the beam. d 280 mm B 1.6 m 120 mm O 254 kPa O 156 kPa O 183 kPa O 204 kPa O 269 kPa Save for Later Attempts: 0 of 1 used Submit Answer
Reinforced And Prestressed Concrete PROBLEM: A reinforced rectangular beam with width b and effective depth d has 4 -16 mm bars placed on 1 layer at the tension side. The beam has a stirrup with a diameter of 10 mm. Use fc=28 Mpa and fy=420 MPa b= 275 mm d= 440 mm L= 3.85 m Wd = 19.25 kN/m WL = 24.75 kN/m Calculate the nominal moment capacity of the beam Calculate that strain of the tension bars. Calculate the strength reduction factor of the beam
Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN 0.8m B 1.5m G 1.5 kN 4 - 1m panels = 4m F
HELP ME PLEASE URGENT!! 3 DECIMAL POINT 1. Determine the design compressive strength of the beam column in KN.02. Determine Cb.0 3. Determine the nominal moment strength of the beam column in KN.m.04. Compute the AISC moment amplification factor.0 5. Determine the required factored load in KN.06. Determine the maximum axial service load P (KN) that can be applied.0
2.) Determine the design positive and negative moments of the beam shown. The dead and live load are 24.3 kN/m and 11.2 kN/m respectively. 7.5m 0.5m
2. The roof truss shown in Figure is pinned at point A, and supported by a roller at point H. Determine the force in member DG and DF.Use method of sections D 55 kN 45 kN MATHalino.com 2.5 m 1.5 m 1.5 m MATHalino.com H. 2 m C 2 m 2 m 2 m 90 kN MATHalino.com
Answer is 260 mm..don't solve incorrect beam is supported by a roller and a hinge at its extremities. The 2 kN/m is loaded entirely on its 4 m length while 5 kN concentrated load is positioned 2 m from the left end of this beam. If the beam is 80 mm wide, determine the minimum height of the beam if the flexural stress is not to exceed 10 MPa.
2. Replace the distributed load by an equivalent resultant force and specify its location from point O on the cantilevered beam 5KN/M O lem VEKNIM * 4m * 4 kN/m 4m 3. De
The billboard shown is supported by structural tube that has a 380 mm outer diameter and 38 mm wall thickness. If the billboard is under wind pressure Pwind and has weigth of Wbillboard, determine the principal stresses and max. in-plane shearing stress at point H. Assume wind is applying uniform pressure all over the billboard and centroid of the billboard is located at point C. You can ignore the thickness of the billboard. P???? =2.3kPa W????????? =80 kN