Determine the source pressure needed to deliver13x10^6 SCFD of CO to a consumer 60 miles away.The pressure at the customer's site must be at least300 lbf/in.2 gauge, according to the agreement. Thepipe is 10 inches long. in circumference At aground temperature of 60°F, long pipelines may betermed isothermal. T = 10°F, p = 1 atm are thestandard settings.a. What is the exit velocity in feet per second, andwhat is the friction factor Fave?b. In psia, what is the pressure at the source?

13×106SCFD60miles away300lbf/in210 inches long60°FT=10°F=469.67RP=1atm To-Find:- a. Exit Velocityb.…

Answered: Determine the source pressure needed to…

Determine the source pressure needed to deliver 13x10^6 SCFD of CO to a consumer 60 miles away. The pressure at the customer's site must be at leas din ato tle o Tle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 18 Describe the T-s diagrams accordingly by filling it the blanks accordingly. Use the sets of words given below for correct description. Ideal / Actual / vapour /cycle /Carnot/ Rankine/ Diesel/Otto/ Brayton/Ericsson/Stirlin g/regenerative/ reheat/ closed open/with/a Wurbout 9in A B P= constant 9in V= constant (b) T-s diagram D 4s 4a G Yout v=const. 9in v=const. E H Yout Yout Wpumpin High-pressure turbine C F Reheating I 4 3 Low-pressure turbine
On the Mindray A5/A3, during the leak test the pressure indicated by the airway pressure gauge fails to reach 30 cmH20. What should you check?
Find the pressure reading for all Pressure Indicators, P11, P12, P13, and P14? A = 125 cm, B = 2 cm, C = 5 cm, D = 10 cm E = 8 cm, F = 2 cm, G = 5 cm, S.G. = 0.92 Blank #1: PI1 = Blank #2: P12 = Blank #3: PI3 = Blank #4: P14 = LIQUID LEVEL D cmWC cmWC cmWC cmWC TOP13 G P14 O P12 E LLOPII
You have an orifice meter that was calibrated for air at 70oF and I atm, You are using it to measure an air flow, and you get an indieaied reading of 25,0 ft3/min at 100oF and 1,1 atm. What is the true gas flow rate in standard (scfm)?
EXPERIMENT -1- TEMPERATURE MEASUREMENT AND CALIBRATION Discussion 1-What are type of thermocouple? 2-What is the difference between the alcoholic and the mercury thermometer? 3-Draw diagram to clarify a relationship between the temperature and a millivolemeter? 4-State any possible error source in the experiment? 5-State any suggestions to improve the experiment?
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand Je oadall i.e.p =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.- 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر Test section 25°C. = 25°C (GATE)
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand e oladall i.e.Pg =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.= 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر 25°C, Test section = 25°C (GATE)
oblems: 1. A horizontal pipe, 1 ft. in diameter, tapers gradually to 8 in. in diameter. If the flow is 500 cu ft. of water per minute, what is the difference between the pressures at the two sections? Ans. PA - PB = 443.63lb per sq ft 2. Water flows through a horizontal pipe at a velocity of 50 ft. per sec. Owing to the pipe gradually expanding to a larger size, the velocity decreases to 35 ft. per sec. What is the difference between the pressures at two points, one in each size of pipe? Ans. Pg - PA = 1,236. 75 lb per sq ft
得分 viscosity of at 40°C. 2. The viscosity (decreases/increases) with the increase in temperature. which 3. The pressure measured relative to atmospheric pressure is can be reported with a negative sign or as vacuums. 4. Absolute pressure is the sum of pressure and local atmospheric pressure. 5. There are two states for fluid flow, i.e. laminar flow and and the state can be determined by 6. The orifice is preferred for flow rate control because 7. Cavitation usually take place at locations like and to search
3. What are the differences between pressure sensor, pressure gauge and pressure transmitter? Explain the above-mentioned pressure measurement devices with an application.
7. The following data obtained during a routine permeability test 70 deg F Find the permeability. Flow rate = 2000 cc of air at 1 atm in 400 sec . Downstream pressure = 1 atm . Viscosity of air at test temperature = 0.02 CP Core cross sectional area = 3 cm² Core length = 5 cm Upstream Pressure = 1.75 atm
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.