Determine the ultimate load distribution acting on all beams and girders in the given floor framing below. Assume that the supports are simply supported. Compute for the reactions and loads in each beam. Assume unit weight of concrete to be 23.6 kN/m³. Always simplify your load distributions (distributed loads acting on the same points/locations should be added up). Monolithic Floor All concrete slabs, t = 100 mm All concrete beams, b = 250 mm; h = 500 mm All concrete columns, 300 mm x 300mm Superimposed Loads Floor Finish: Ceiling: Ceramic tile ½ inch mortar Frame Partition: Exterior Walls Wood furring Gypsum board 14 inch thick Mechanical Duct Allowance (MDA) Utilities: twice the weight of MDA Live Load Wood, studs with gypsum board h=2.8m 5m A H 3m Normal Unit Weight Concrete Masonry/ Concrete Hollow Blocks, CHB 4 inch thick with plastering on both faces, full grout height=3m (no interior walls) Residential NOTE: REFER TO NSCP 2015 CHAPTER 2 FOR THE MINIMUM DESIGN LOADS. USE LRFD LOAD FACTORS: 1.2 DL + 1.6 LL B G 2m C F 2.5m D

Determine the ultimate load distribution acting on all beams and girders in the given floor framing below. Assume that the supports are simply supported. Compute for the reactions and loads in each beam. Assume unit weight of concrete to be 23.6 kN/m³. Always simplify your load distributions (distributed loads acting on the same points/locations should be added up). Monolithic Floor All concrete slabs, t = 100 mm All concrete beams, b = 250 mm; h = 500 mm All concrete columns, 300 mm x 300mm Superimposed Loads Floor Finish: Ceiling: Ceramic tile ½ inch mortar Frame Partition: Exterior Walls Wood furring Gypsum board 14 inch thick Mechanical Duct Allowance (MDA) Utilities: twice the weight of MDA Live Load Wood, studs with gypsum board h=2.8m 5m A H 3m Normal Unit Weight Concrete Masonry/ Concrete Hollow Blocks, CHB 4 inch thick with plastering on both faces, full grout height=3m (no interior walls) Residential NOTE: REFER TO NSCP 2015 CHAPTER 2 FOR THE MINIMUM DESIGN LOADS. USE LRFD LOAD FACTORS: 1.2 DL + 1.6 LL B G 2m C F 2.5m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Reinforce Concrete Design The beam section shown in the Figure 3 will carry the same loading pattern in ProblemNo.3 , Figure 2(b). If the value of Pu = 175 kN and using design properties of f’ c = 30MPa and fy = 345 MPa, determine the following:Need to answerThe shear capacity of the concrete alone and the ultimate critical shear force at the right side of the left (hinge) support (interior face).
Determine the ultimate load distribution acting on all beams and girders in the given floor framing below. Assume that the supports are simply supported. Compute for the reactions and loads in each beam. Assume unit weight of concrete to be 23.6 kN/m3. Always simplify your load distributions (distributed loads acting on the same points/locations should be added up). Monolithic FloorAll concrete slabs, t = 100 mmAll concrete beams, b = 250 mm ; h = 500 mmAll concrete columns, 300 mm x 300mm Superimposed LoadsFloor Finish:Ceramic tile ½ inch mortar Ceiling:Wood furringGypsum board ¼ inch thickMechanical Duct Allowance (MDA) Frame Partition:Wood, studs with gypsum board h=2.8m Utilities: twice the weight of MDA Exterior WallsNormal Unit Weight Concrete Masonry/ Concrete Hollow Blocks, CHB4 inch thick with plastering on both faces, full groutheight=3m (no interior walls) Live LoadResidential
TITLE: ANALYSIS OF Reinforced Concrete Beams (SERVICEABILITY REQUIREMENTS). PROBLEM: Check the serviceability requirements in terms of deflections. Assume concrete weighs 23.5 KN/m³, fy = 414 MPa, and f'c = 28 MPa. PLI = 133 kN PLI = 89 kN WDL = 29 KN/m + Selfweight of beam 1.2 m 1.2 m 2.4 m 78 тm 4 - #32 800 тm 722 тm 400 тm COMPUTATION: Required: 1. Check serviceability requirement using 480 (span length) as the allowable. a. Short term deflection b. Long term deflection assuming 50 % of liveload is continuously applied for 4 years.
The concrete post shown is reinforced axially with four symmetrically placed steel bars each of cross-sectional are 900mm^2. If the 1000 kN axial load is applied and the moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Determine a) the stress in each of the steel bars, and b) the stress in the concrete.
The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E = 25 GPa for concrete 900 KN 250 mm 375 mm
Problem 1 The members of the truss shown below are of plain concrete. The compressive cylinder strength of concrete is 30 MPa. Determine whether the structure can carry the applied load. 31 KN 24 KN D 120x120mm 40x40mm 40x40mm 120x120mm 300 mm 40x40mm 400 mm
Situation 1: A concrete overhang beam with the section shown is to support a 150 mm thick concrete slab with a tributary width of 2.70 m. The beam also supports a 3.20 m height of 100 mm thick concrete partition wall. Unit weight of concrete is taken to be 24 kN/m³. Determine the dead load in kN per meter length of beam and determine the maximum fiber stresses (tensile & compressive) due to the imposed dead loads. Draw the complete V&M diagrams. 14 b1 300 mm b3 10.0m G1 120 mm 360 mm LIBRARY Situation 2: Shown below is a floor plan of the library, office and balcony at the second floor level of a condo unit. Use the floor live loads for the given areas: Library area, LL = 5.60 kPa; for Office, LL = 3.20 kPa; and for the Balcony, LL = 2.40 kPa. Determine the live load intensity and load condition to be applied on each member (b1,b2, b3, b4, b5, G1, G2, & G3. Determine also the internal shear and internal moment at the midspan of girder G2. BALCONY G2 G3 4.0m b2 b4 1.2 m FLOOR PLAN 8.0m…
!! Show Complete & Detailed Solution w/ FBD !!The concrete post in the figure, is reinforced axially with four symmetrically placed steel bars, each ofcross-sectional area 750 mm2. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. A 2000-kN axial load is applied. Compute the:a. axial force in concrete;b. axial force in the steel bars;c. stress in the concrete;d. stress in the steel bars;e. deformation of the concrete post.
Situation 1: A concrete overhang beam with the section shown is to support a 150 mm thick concrete slab with a tributary width of 2.70 m. The beam also supports a 3.20 m height of 100 mm thick concrete partition wall. Unit weight of concrete is taken to be 24 kN/m³. Determine the dead load in kN per meter length of beam and determine the maximum fiber stresses (tensile & compressive) due to the imposed dead loads. Draw the complete V&M diagrams. -wall 300 mm 120 mm slab 1.2 m 4.8 m 360 mm
Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a live load of 30 kN/m. The prestressing force is KN. [Take permissible stresses in concrete and steel as 15 MPa and 1200 MPa respectively]
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm