Do it fast thanku Tool changing time is 5.4 min.Taylor's tool life exponent is 1.3Determine tool life for maximum productionrate?

Given; Tool changing time is=5.4 min Taylor's tool life exponent=1.3 Acc. to data given we have to…

Answered: Determine tool life for maximum…

Engineering

Mechanical Engineering

Determine tool life for maximum production

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter1: Introduction To Machining

Section1.1: Introduction To Machining

Problem 10RQ: Abrasive machining makes use of ______ to remove material.

See similar textbooks

Related questions

Q: This weldment is subject to an applied force F=12 kip, weld size h=1/4 in, and the weld is made with…

A: Welding is a fabrication process in which two or more than two parts are fused together using heat…

Q: k The 8.8 kg block is attached to a spring (k = 214 N/m) as shown. The small wheels serve to…

Q: 1. The resistivity of aluminum is 2.8 x 10-8 0m. How long (in meters) a piece of aluminum wire 1.0…

A: Find how long a piece of aluminium wire is needed to give a resistance of 4 ohm's

Q: A wind tunnel has an inlet section with a velocity of 360 ft/s at standa atmospheric conditions. The…

A: Ans: 403 ft/sec

Q: Problem 2. A steel tube of outer radius 5.8 cm is used to axially support a 100 kN load. If the…

Q: A standard tractor trailer truck travels down the highway at 46.7 mph. The truck is 8.5 ft wide and…

Q: Torque is the rotational equivalent of kinetic energy force linear momentum…

A: Correct answer: 2. force

Q: A car is moving on a straight road 20 m/s. It is acceleration at 34 m/s?. What will be it's velocity…

Q: ciate between oper

A: solution of above problem is below

Q: Find the transfer Function of this translational Mechanical system X2 (t) X1(t) f(t) 2N m oll M1 X1…

Q: 50 KN/m Determine the vertical deflection at the free end and the slope at the left support of the…

Q: 1. Determine the moment about the center of the bolt in the drawing below. (answer: 8.31 N-m CCW) 80…

A: Rotational effect of force about a point is called as moment. Moment = Force X Perpendicular…

Q: (b) Consider a simple ideal Brayton cycle with air as the working fluid. The pressure ratio of the…

Q: 3. For an ideal diesel cycle, the pressure at the beginning and at the end of compression are 98 kPa…

Q: Algebra tx) 75 B0 93 65 87 71 98 84 77 Statistics (y) 82 78 86 72 91 80 95 72 89 74 Fnd the…

A: Given Marks of students in Algebra and statistics To find Summation of X Summation of X2 Summation…

Q: Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg.

Q: An airplane is flying at an altitude of 12 km at 100 m/s. What is the equivalent velocity of the…

A: dynamic pressure must be same.

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

Q: A rocket is launched vertically at time t = 0. The elevation of the rocket is given by y = -0.14t“ +…

Q: W = 200x N/m C В 2 m 3 m

Q: Is truss stable or not

A: Introduction : The structure is truss structure in which their are 13 members connected by 8 joints…

Q: A double overhung impulse turbine of 85% efficiency is direct-connected to a 30-MW generator of 93%…

A: Given Hydraulic efficiency = 85% Power = 30 MW Generator efficiency = 93% Head elevation = 832 m…

Q: A fuel consist of 84% Carbon, 13% Hydrogen, 2% Oxygen, and the remainder incombustible solid matter.…

A: given : carbon -84% hydrogen -13% oxygen- 2%

Q: True or False: 1. As temperature rises, mach number is greater 2. An airplane flying with mach…

A: Soln:- 1 st statement :- As temperature rises , the speed of sound is faster . But the speed of…

Q: 3. Gear B supplies 20 KW of power, while gears A, Cand D withdraw 6 kW, 4 kW and 10 kW,…

A: Answer: The required minimum diameter of the shaft is 24.5 mm.

Q: an "open system" is one in which mass cross its boundaries True False pV = mRT is made from the…

Q: Need in 1 hour please, thank u! If a twisting moment of 10,000 lb-in is impressed upon a 1 and 3/4…

Q: Find the centroid of the plate shown in the figure. 1.5 1.5 1 10

A: Find the centroid of the section.

Q: ans fast

A: PH=P1=6MPaP2=P3=2MPaP4=P5=20 kPaQB=58,416 kJ/secm˙=20kg/sec So, the dryness fraction at 4 will be…

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

Q: ENGINE LATHE PROCESSES History of engine lathe Types of engine lathe Parts of an…

Q: By considering a notched metal bar as an example, explain (with the aid of diagrams), how you would…

A: The development and propagation of fractures in a material owing to cyclic stress is known as…

Q: 2. Calculate the torque on the bolt for a force applied at point A = (3,4) ft and perpendicular to…

Q: ifferentiate Refrigerator from Heat pumps in terms of: (a) Transfer of Heat, (b) Location of the…

A: Given Refrigerator Heat pump To find Differences

Q: A geothermal power plan has the following data: specific enthalpy at final stage equal to 28.5…

A: Given data:

Q: About characteristics of steady flow system: There is either accumulation or diminution of energy…

A: Steady flow: The flow in which fluid and its energy enters and out from an open system at steady…

Q: amber. Both fuel and air initially a. - Take CPf kJ 1.9 kg.K %3D

Q: An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the…

A: Calculate the moment of inertia of the column about the y-y axis i.e. the vertical centroidal axes.…

Q: If the Taylor tool life exponent is 0.1 and the tool changing time is 1.6 min, then the tool life…

Q: A liquid flows through a pipe with a diameter of 15 cm at a velocity of 10 cm/s. If the diameter of…

Q: 1. A circular furnace has 2 end black surfaces and surface 1 is kept at 500 K and surface 2 is kept…

Q: A The following are the weights in pounds of 10 pieces of balikbayan luggage: No. 3. 4 6. 7 8 9. 10…

A: Given data No Weight 1 124 2 125 3 125 4 123 5 124 6 127 7 125 8 126 9 121…

Q: PROBLEM NO. 1 A rocket is launched vertically at time t= 0. The elevation of the rocket is given by…

Q: Assume a steel pipe of r, = 10 mm, exposed to natural convection at h = 50 W/m².K. This pipe is…

Q: 4. A spherical vessel of 1.7m diameter is made from 12mm thick plate, and it is to be subject4 to a…

A: Given data: d=1.7 mt=12 mm∆P=116 bar=116×10-4 GN/m2k=2.9 GN/m2E=200 GN/m2v=0.3 Need to determine the…

Q: Compute for the value of the item required: 1. Vertical Reaction at D 2. Horizontal Reaction at D…

A: Let FG be the force in the member G. Let as represent the weight of the block as "W". ⇒W= 800 lb…

Q: The two disks A and B have a mass of 3 kg and 5 kg, respectively. If they collide with the initial…

Q: Consider the following alr-condltlonIng system design whlch Involves a refrigeration process…

Q: The 3rd term of an arithmetic series is 34 and the 17th term is -8. Find the sum of the first 20…

A: Find the sum of first 20 terms in arithmetic series.

Concept explainers

Processing of Polymer Matrix Composites

The polymer matrix composite is described as a composite material that contains some polymer in the form of either fibers or powder. Polymer matrix composites are also known in short as PMC's.

Question

Do it fast thanku

Tool changing time is 5.4 min.
Taylor's tool life exponent is 1.3
Determine tool life for maximum production
rate?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In machining operation, if velocity doubled then the 1ool life reduced to 1/16 th of initial value. Taylor's tool life index (n) for a machining operation is
In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value. What is the Taylor's tool life index (n) for a machining operation?
In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value find the Taylor's tool life index (n) for a machining operation.
Q1:- Put a mark of True or false for below:- (a):- The milling cutting tool has a single cutting edge? (b):- At the break-even point, the total revenue equals the total cost? (c):- The right-hand rule is used to define machine axes? (d):- Design error is a simple mistake? (e):- The quality of products is poor in mass production? (f):- Allowances must be left before turning? (g):- Up-ward milling is better than down-ward milling?
Q3 Provided below is the Tool life data for cutting low carbon steel with HSS tool. Draw the tool life relation and 1- find the n and c exponent for the tool life equation 2- find the cutting speed for 14 min tool life Cutting Speed (ft/min) 250 180 150 100 Tool Life (min) 2 5 10 30
Question: Determine the optimum cutting speed for an operation on a Lathe machine using the following information: Tool change time: Tool regrinds time: 3 min Machine running cost Re.0.50 per min Depreciation of tool regrinds Rs. 5.0 The constants in the tool life equation are 60 and 0.2 3 min
Make a comprehensive write up on tool-wear and tool life with due reference to cutting speed and tool life. ( Manufacturing process)
The tool life equation for HSS tool is VT0.14f 0.7d 0.4 = Constant. The tool life (T) of 20 min is obtained using the following cutting conditions: V = 40 m/min, f = 0.30 mm, d = 2.0 mm If speed (V), feed (f) and depth of cut (d) are increased individually by 25% . Calculate the tool life.
In a drilling operation under a given condition, the tool life found to decrease from 20 mint to 5 mint due to increase in drilling speed from 200 rpm to 400 rpm. What will be the tool life of that drill under the same condition if the drill speed is 300 rpm.
40 1. taylor equation II. increased power III. microstructure might be measured IV. toughness might be measured Which method(s) is (are) used for determining of tool life criteria in production? a) Il and III b) I, Il and III C) I and II All of them Only I f) 1, IIl and IV
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
In a production turning operation, the workpart is 60 mm in diameter and 500 mm long. A feed of 0.75 mm/rev is used in the operation. If cutting speed-9 m/s, the tool must be changed every 4 workparts; But if cutting speed=5 m/s, the tool can be used to produce 50 pieces between tool changes. Determine the Taylor tool life equation for this job. (use the equations given below for solution) L Tm- 1,= Nf N AD, vT" = C %3| AD,L Tm fv