Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter54: The Operational Amplifier

Section: Chapter Questions

Problem 7RQ: Name two effects of negative feedback.

See similar textbooks

Similar questions

(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution
In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank comes at constant flow rate and steam is coming from a valve to maintain the pressure. A pressure gauge is used to measure the water pressure in the tank. a. Provide the block diagram representation using a PID controller for the above mentioned condition (Control the pressure using the proportional valve.). b. explain the working principle.
Human-aided control system for controlling a fluid level in a tank is shown in Figure Q2a. Here H denotes the fluid level inside the tank in meter and Qout be the outflow rate of the fluid from the tank and Qin be the inflow rate of the fluid into the tank. Construct the functional block diagram and identify the controlled variable, controller, actuator, process/plant and measurement element. H Qout Valve
Name two effects of negative feedback.
Identify the following elements of the given closed loop control system.(i) Process Element(ii) Feedback Element (iii) Control Element (iv) Correction Element
4. Consider a batch process of the conveyor oven illustrated in Figure 1. List all input and output process variables involved (binary and continuous), and draw the block diagram for the automation of the conveyor oven temperature and the connection schematic of the programmable logic control interface with process field devices. Motorized circulating fans Airflow (m/s) Electrical heating elements Heater voltage (volt) ww. Thermostat Thermostat ("C) ("C) 111111tt, Cake Cake Cake Cake Cake Cake II Travel direction Screw conveyor Stepping motor Figure 1: Cake conveyor oven.
Conventional float actuated device is used as a level measurement sensor, which consist of pulley and a pointer which move over a graduated scale. Let say you are asked to develop a controller-based float actuated system having a sensor for level measurement or may be more than one sensor is required for accurate level measurement, which sensor will you use and why? Draw the whole schematic showing the position of the sensor or sensors. Will pulley be part of your new digital system, if yes justify your answer, if no, then how you will develop a system without using pulley.
Sample question 1 Figure shows a vehicle speed control example block diagram. Apply block diagram reduction and find?(?).
I want you to draw a ladder logic diagram of a garage door to control it by PLC. In my case we have different inputs and outputs and all of them gotta be used in the diagram. I can perfectly interpret the diagram so no need to explain it, I will just require you to draw it. INPUTS : open push button ( OPB ) - close push button ( CPB ) - open limit switch ( OLS ) - close limit switch ( CLS ) - obstacle detection sensor ( ODS ) - safety sensor ( SS ) - emergency stop push button ( ESPB ) - reset button ( RB ) OUTPUTS : motor starts ( MS ) - motor stops ( MSTP ) - motor forward ( MF ) - motor reverse ( MR ) - Error display ( ER ) OPERATİNG MODES : automatic mode ( AM ) - manual mode ( MM ) NECESSARY TIMERS : T1 ( delay door movement after obstacle detection ) - T2 ( delay door movement after reversing ) Here is my excercise for today. Please I am requiring a good logic diagram taking into consideration all what was mentioned before. so to sum up, I want you to write a logic ladder diagram…
Which claim is correct? A transfer function model for a stable process always has no time-delay. Feedforward control can be solely used for the setpoint tracking If a process has 3 inputs and 3 outputs, then we need to build 6 transfer function models for it. The inner loop of cascade control has to be slower than the outer loop No correct answer
The ratio of output to input of a system is known as Transfer function. Select one: O True O False Coloct the cinmple cuctom fcom the fellouuing
4:01 A moodle.nct.edu.om Question 1 Not yet answered Marked out of 1.00 P Flag question In type of system ,the input and output have direct connection in between. O a. Dynamic O b. Closed loop O c. Static O d. Open loop Question 2 Not yet answered Marked out of 1.00 P Flag question Air conditioner is an example for less accurate system. Select one: O True O False Question 3