Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how did you draw the glass box/isometric box.

Q: support. E=200 GPa and I=65x105 mm 3m

A:

Q: A 3m-LONG CANTILEVER BEAM IS CARRYING A UNIFORM DEADLOAD OF 20 kN/m (EXCLUDING SELFWEIGHT OF THE…

A: wD = 20 + 0.3 x 0.6 x 23.5 = 24.23 KN/n wL = 15 KN/m Wu = 1.2 WD + 1.6 WL = 1.2X24.23 + 1.6X15 =…

Q: C O N S T R U C T I O N  M A T E R I A L S  A N D  T E S T I N G not less than 3 sentences…

A:

Q: Given data: Maximum principal stress=38 MPa Minimum principal stress=32.5 Mpa Find maximum shear…

A:

Q: 4 m X B m- P₁ 3 m- P2 C D

A: Given data  P1 = 10 KN P2 = 20 KN From the given figure, it can be seen that joint A, B and C are…

Q: b) A rectangular block of 1200 mm² cross-sectional area is subjected to a longitudinal compressive…

A: The angle given is 40 degrees

Q: Take P=175 kN and E=200 GPa Determine the sign and magnitude of deflection at point D using the…

A: For W 410×114, moment of inertia about x-axis is  I = 462 × 106 mm4   E = 200GPa = 2 × 105 N/mm2…

Q: A vertical steel rod is fixed at top and supports an 8-kN load at the lower end. The rod is 10mm in…

A:

Q: A soil sample with a grain specific gravity of 2.67 was filled in a 1000 mL container in the loosest…

A:

Q: Find the hydraulic radius of rectangular channel having wetted area 16 m2 and wetted perimeter 12 m

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: In the Hirakud hydroelectric power station, there are four Kaplan and two Francis turbines,…

A: Given: The average head is 26.5 m. The overall efficiency of the Kaplan turbine is 90%. The overall…

Q: sample has a total mass of 23.3 g a volume of 12 cm³, an oven-dry mass of 21.2 g, and a specific…

A:

Q: A Compound Circular Horizontal Curve Have :, A ₁ =42° 16`, E ₂ =38.08 m · AZP.CP.1=62°12` AZP. →…

A:

Q: 46 34 45 43 Other:

A:

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. 9 с 200 mm…

A:

Q: Need it asap. Question: Regarding on the yellow line, why it became h^-½dh ? And on the red shape,…

A: To find time needed to empty the pool

Q: A right-angled triangular channel carries a flow of 16,000 l/s. The Manning’s n = 0.020 and the…

A:

Q: g at 4 m/s through water. Estimate the por of the log is parallel to the tow direction

A: νw=1.12×10-6m2sρw=998.8kgm3Re=vDν=4×21.12×10-6=7.14×106so,Aspect ratio =LD=82=4For circular ract…

Q: 9.12 Water flows past a flat plate that is oriented parallel to the flow with an upstream velocity…

A:

Q: Explain the process to comprehensive land use planning step-6 Establish development thrust and…

A: The Comprehensive Land Use Plan process in the Philippines is composed of 12 steps. Step 6 is to…

Q: 4. A trapezoidal masonry retaining wall 1 m wide at top and 3 m wide at its bottom is 4 m high. The…

A: Given: A trapezoidal masonry retaining wall 1 m wide at top and 3 m wide at bottom and 4 m height…

Q: 4. A point X on a simple curve has a deflection angle of 18 degrees with the back tangent. The…

A:

Q: 9.43 A baseball is thrown by a pitcher at 95 mph through standard air. The diameter of the baseball…

A: TO Determine Drag force on the baseball.

Q: 11. Method of Superposition Problem 4. Draw the moment diagram for the beam using method of…

A:

Q: Consider a wood beam (see figure) carrying a uniform load of 21.5 kN/m (which includes the weight of…

A:

Q: al-sized pieces and arranged as sh ermine the ratio of the drag on the or the drag on the plates in…

A: Drag force is given…

Q: 9.47 If the drag on one side of a flat plate parallel to the upstream flow is when the upstream…

A: Force due to drag is FD=CD(12ρAU2)CD=1.32δReCD=1.32δUlμso,FD=(1.32δUlμ)(12ρAU2)FD∝U32

Q: explain the application of high-performance steels.

A: Here mentioned some important application of high performance steels.

Q: A composite beam is constructed using a steel plate (15 mm x 145 mm) with two wood beams (75 mm x…

A: Figure is as shown

Q: Determine the slope and deflection at C by the conjugate beam method. E = 200GPa and I = 500x106mm4.…

A:

Q: Draw the axial load, shear and bending moment diagrams for the frame shown. 30 kN/m B xoxo A 4 m

A:

Q: The specific gravity of a saturated soil sample is 2.60, with a total unit mass of 2250 kg/m³. The…

A:

Q: Draw the axial load, shear and bending moment diagrams for the frame shown. 30 kN/m B C 3 m 5 m +…

A: We will calculate reactions and draw FBD.

Q: A B с D FL оооо 0 0 0 с 3 G =

A:

Q: a. When you place a door on a wall, how do you switch the direction?

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: A shot is fired at an angle of 45° with a horizontal and a velocity of 300 fps. Find the height and…

A:

Q: A W 530 x 85 with Fy = 345 MPa is used for the beam and loads of the figure below. Use LRFD of NSCP…

A:

Q: Given data : Depth of flow=2 m Velocity of flow=3 m/s g=10 m/s2 Find specific energy

A:

Q: Question-4: An open layer (doubly drained) of clay 4 m thick is subjected to loading that increases…

A: step 1-

Q: A 9.0m span building roof is formed by a statically determinate pin jointed, triangulated framework,…

A: Area (152x152x23) = 2920mm2 Area (80x80x8) = 1230mm2 Apply unit vertical load at E for deflection…

Q: ht repre part las = elocity v = 6 ft/sec in the direction shown and Las acceleration components ax…

A:

Q: he beam with cross-section shown carries a uniformly distributed load of intensity w ove s entire…

A:

Q: 9.40 A 50-mph wind blows against an outdoor movie screen that is 70 ft wide and 20 ft tall. Estimate…

A:

Q: Analyse the rectangular two way slab for the yield pattern -1 (as shown below) by equilibrium…

A:

Q: If the free end of a cantilever of span / and flexure rigidity El undergoes a unit displacement…

A:

Q: Pls help me. I will rate 5 stars and leave a positive feedback.   One-way Slab Design Problem…

A: Solution: Given:  Unit weight of concrete = 25 kN/m3  DL =5 kPa (excl. self weight)  LL = 3 kPa  fy…

Q: Determine load requirements for LM1 for loaded length 35m, assume the carriage width of 10m

A: Given Data: Length = 35m Carriage width = 10m

Q: +Tabulated Data and Result, Modulus of Rupture Sample No. L (mm) b (mm) h (mm) 1 730 50 50 2 730 50…

A:

Q: find all reaction for the frame shown by The slope deflaction method B hinge с Fin 2 WL 12 3 3 find…

A: Fixed End Moments

Q: A static third-point bending test was performed on a 100mm x 100mm x 5000mm wood sample according to…

A: