THIS QUESTION REQUIRES A DOCUMENT UPLOAD A temperature control system has a binary input represented as ABCD, with A being the most significant bit. When the temperature is in an acceptable range we need the output of the control system to be one. We are in the acceptable pressure range when ABCD represents a decimal number from a minimum to 5 to a maximum of 12. When we are in this range the system output is one. However, if ABCD represents a decimal number of 4 or less, or 13 or more, the system should output a 0. a. Complete the truth table for this system b. Create a Karnaugh map for this system c. Based on the Karnaugh map, determine the simplest Boolean expression for this system d. Draw the simplified circuit that represents the Boolean expression found in step c. Complete your work on separate paper, then scan and upload your answer. YOU MUST SHOW ALL YOUR WORK TO RECEIVE CREDIT FOR YOUR ANSWER Upload Choose a File

THIS QUESTION REQUIRES A DOCUMENT UPLOAD A temperature control system has a binary input represented as ABCD, with A being the most significant bit. When the temperature is in an acceptable range we need the output of the control system to be one. We are in the acceptable pressure range when ABCD represents a decimal number from a minimum to 5 to a maximum of 12. When we are in this range the system output is one. However, if ABCD represents a decimal number of 4 or less, or 13 or more, the system should output a 0. a. Complete the truth table for this system b. Create a Karnaugh map for this system c. Based on the Karnaugh map, determine the simplest Boolean expression for this system d. Draw the simplified circuit that represents the Boolean expression found in step c. Complete your work on separate paper, then scan and upload your answer. YOU MUST SHOW ALL YOUR WORK TO RECEIVE CREDIT FOR YOUR ANSWER Upload Choose a File

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

What is an MSDS?
Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F= YO Y Y, Y, D. Y. Decoder O a. B' O b. C O'c.B O d. C
A multiplexer a. Selects where data should be sent b. Selects one out of several data input lines c. Has a single input and converts it to a binary output d. Has a binary input and converts it to a single output
A multiplexer a.Takes a single data input and routes it to one of several outputs b.Selects from many data sources c.converts a binary code input to a single output d.converts a single input to a binary code
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
The figure below shows a multiplexer where S, and S, are the select lines. I, to I, are the input data lines, EN is the enable line, and F(P, Q, R) is the output. F is EN R F MUX R 12 13 S, So P Q
Code ConverterCreate a circuit that converts NBCD code into 5311 code. If the input is not part of the NBCDcode, the output is all 1.Input:4 -bit NBCD code Output:4-bits 5311 code Hint:You must create a Karnaugh map for each output bits.
Q1: Design and draw time diagram of MOD-10 asynchronous/down counter that counts as 0000 to1001 knowing that Clock type is Negative and Output is taken from Q? Q2: Design and draw time diagram of asynchronous/UP counter that counts as 0001 tol001 knowing that Clock type is Negative and Output is taken from Q? Q3: Design 4- bit UP/DOWN Ripple Counter using j-k Flip-Flop
1-With most monostable multivibrators, what is the Q output when no input trigger has 2- The bit sequence 10011100 is serially entered (right-most bit first) into an 8-bit parallel out Q5A: - Choose the correct answer for each question occurrèd? A. LOW, B. +5V, C. SET, D.HIGH shift register that is initially clear. What are the O outputs after four clock pulses? A. 10011100 В. 11000000 C. 00001100 D. 11110000 S-11 an 8-bit ring counter has an initial state 10111110, what is the state after the fourth clock pulse? A. 11101011 В. 00010111 С. 11110000 D. 00000000 4- A 555 timer in monostable application mode can be used for A. Pulse position modulation B. Frequency shift keying C. Speed control and measurement. D. Digital phase detector.
design and draw the full circuit diagram for the control circuit for the pc register
Q1. Show the implementation of 4 bit binary to gray code (shown in below table) converter using either EPROM or PLA. In Gray code only one bit changes at a time. Binary Gray code Decimal equivalent 0000 0000 1 0001 0001 0010 0011 3 0011 0010 4 0100 0110 5 0101 0111 6. 0110 0101 7 0111 0100 8. 1000 1100 1001 1101 10 1010 1111 11 1011 1110 12 1100 1010 13 1101 1011 14 1110 1001 15 1111 1000
• An 8 words x 14-bit ROM (i.e., having 8 addresses which stores 14 data bits) has the following arrangement and corresponding truth table: Input lines (ROM address) 000 001 Output lines Cin y A1 A2 АЗ SL1 SL2 S2 So (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1