erodynamics NACA 1415, the maximum camber is 8.4 cm 1) What is the chord length? 2) What is the position of maximum camber from LE?

Q: A 1.5 mean diameter flywheel, 600kg weight changes its speed from 240 to 230rpm during shearing…

A:

Q: Calculation for slider crank When, ? = 100 rad/???2 R=62.5mm L=260mm ? = 90 ? = 100 ???/??? Find :…

A: X = Lcos ϕ + R cos θ cosϕ =(1- (R/L)2 sin2θ)  cosϕ = 0.9706 X = 260 *0.9706 + 62.5 cos90 X = 252.356…

Q: Human Factors Engineering Q1) Dark to light adaptation takes place very slow ? A)True B)False Q2)…

A: Adaptation: The ability of the retina of the eye to adjust different levels of light is known as an…

Q: Calculate the value of pole pitch (in SI unit) for mean air gap radius= 0.8mm and P=

A:

Q: Q3:Find the cocfficient of fluctuation of speed of a petrolengine runs at 1745r.p.m knowing that the…

A: The total change in energy from the turning moment data can be given as - ∆E =…

Q: Do you think that the Aberdeen Three knew about RCRA? If not, should they have? Does it really…

A: The actions of the three engineers bring to mind an important question. These engineers were…

Q: A 4 stroke, 3 liter engine runs at 2000 RPM, and delivers 100 kW of brake power and consumes 350…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: 1. What are the most important motivations behind analytically investigating car crashes?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: You have engaged in open discussion in which you have to evaluate the conditions needed for an…

A: The work of differential is to provide different power to the different output shafts. This…

Q: concepts regarding circle were applied to a steering

A:

Q: Calculate the swept volume and mean effective pressure (MEP) of a 4-Cylinder, 2-stroke IC engine…

A: Given Data: Mechanical efficiency, η=90% Number of cylinders, n=4

Q: Q 2. (a) Why mechanical actuators are used in mechatronic system? What is the use of cams and…

A: Given Mechanical actuators Cams Example of ratchet and pawl design Hydraulic and pneumatic actuator…

Q: amshaft bearing shell what material can be used ? why. Explain the properties of material

A: The cam bearing's principal function is to support and spin the camshaft, allowing it to open and…

Q: 1) What is the CL? 2) What is the position of maximum camber?

A: NACA stands for National Advisory Committee for Aeronautics. In the problem, a NACA 5 digit code…

Q: The pinion transmits 400 horsepower at 2000 rpm from a wheel single reduction straight gear. The…

A: Given: The power of the pinion is 400 hp and speed is 2000 rpm. The center distance is 60 cm. The…

Q: Explain the commonly used alteration method used by car racers.

A: Car alteration or tuning is the process of modifying a vehicle to optimize it for a different set of…

Q: 5) Improvements to engine design and aerodynamics are improving all the time. f Is there a limit to…

A: Given Vehicle To find Vehicle can travel on full tank of gas or battery charge for one day

Q: 7. What are the rotating wheel positioning parameters? What is the role of each? Why does the rear…

A: Wheel positioning is of the maintenance of automobiles. It is sometimes called breaking or tracking.…

Q: Explain the Coefficient of Performance?

A: Coefficient of performance (COP): It is the ratio of the desired energy to input work. The desired…

Q: scuss the impact of drafting or drawing in future mechanical enginee

A: we will discuss the impact of drawing or drafting in  future

Q: TRUE or FALSE. Please provide a quick explanation thanks! 1. Each molecule of a system has a…

A: Statement 1 is True.  Each molecule of a system has a certain quantity of mass, thermal energy, or…

Q: NACA 25012 Chord c = 150 cm 1) What is the CL? 2) What is the position of maximum camber

A:

Q: 12) Write the linear model of a front tire for longitudinal and lateral forces, as functions of…

A: The non-linear vehicle model can be linearized by assuming the small angle approximation and…

Q: Reciprocating engines also known as the piston-cylinder device has proven to be very versatile…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Q: What is the differnce between KPI and camber in Automotive industry?

A: given; What is the difference between KPI and camber in Automotive industry?

Q: NACA 25012 Chord c = 150 cm 1) What is the CL? 2) What is the position of maximum camber?

A: To find: The value of CL. Given: The value of c=150 cm. Formula used: Consider first digit as 2. The…

Q: In the wind experiment, what blade pitch angle results in maximum power output? O a. small and…

A:

Q: There are three basic categories in high-performance automobiles. Dissect each of these categories…

A: Hii, thanks for the question but we are authorized to answer one question at a time since you have…

Q: How do a unicycle and a twoaxle car react differently to road bumps?

A: Unicycle car: Most of the unicycles do not come up with a suspension system. Hence, there is not…

Q: If the line of best fit for your torque speed curve is described by the following equation. Given…

A:

Q: Write introduction ,definition,advantages and disadvantages, examples and conclusion about relative…

A: Relative motion : The concept of reference frames was first introduced to discuss relative motion in…

Q: The age of a car driven is qualitative or quantitative and why?

A:

Q: The blade on a circular saw has a radius of 0.100 m from the center to the tip of one of the blade's…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: From Bartov’s observations, what are the pluses and minuses of America’s car culture? In what ways…

A: The pluses of  Bartov’s observations of America’s car culture include independence and freedom to…

Q: NACA 6412, Chord = 100cm 1) what is the maximum camber? 2) What is the position of maximum camber…

A: Given, Chore length (C) = 100 cm

Q: What are the different applications of the principle of virtual work in mechanic?

A: Virtual work is the work done by a real force acting through a virtual displacement or a virtual…

Q: You want to put larger tires on your truck. The manufacturer tires are P265/65R18. You want to…

A: As per the company guidelines we will answer the first three subparts for you, for the remaining…

Q: Explain about derivation of shaft strength...?

A: Derivation of shaft strength ;

Q: Draw a sketch of a typical CL vs angle-of-attack curve and a CD vs CL curve, and show how increasing…

A:

Q: kinetics of particles-relative motion report

A: kinetics of particle-relative motion

Q: The term "Slowly shifting dimension" should be defined and explained.

A:

Q: decimal places on final answer, and in scientific notation for less than 1 values. Include the units…

A:

Q: Explain as simple as possible. Question: What is the minimum motion increment on a CNC in imperial…

A: It is asked to find minimum motion increment on a CNC in imperial units.

Q: Initially at rest, a gear starts rotating with a constant angular acceleration a = 5 rad/s². What is…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: List FIVE differences between NC and CNC systems indicating the major advantage gained with each…

A: NC Systems (Numerical Control ) CNC Systems ( Computer Numerical Control) In this the control of a…

Q: Q2 (a) List several types of flexible drive system and its application in real engineering.

A: Different types of flexible drive system and it's application

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.