Example -5.2-It is required to pump cooling water from storage pond to a condenser in aprocess plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d.pipe is available and the pump has the characteristics given below. The headloss in the condenser is equivalent to 16 velocity heads based on the flow inthe 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow andthe power to be supplied to the pump assuming n = 0.5Q (m³/s) 0.0028 0.0039 0.0050.0056 0.0059Ah (m)23.221.318.915.211.0

Please Rate if this solution helps youThank You

Answered: Example -5.2- It is required to pump…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A supply water is available at a head of 684 meters. It is proposed to build a turbine to operate at 6 rev/s and develops 14.92 MW.Compute the specific speed in rpm.a. 3297rpmb. 4356rpmc. 6568rpmd. 3477rpm
1 Add file Q4) A SI engine four-stroke cycle V8, 0.005m3 displacement, mounted on a hydraulic dynamometer has an output of 53,6 kW at 405O RPM. Water absorbs the energy output of the engine as it flows through the dynamometer at a rate of 0.113 m3 per minute. The dynamometer has an efficiency of 93% and the water enters at a temperature of 20°C.Calculate: (a) Exit temperature of the water. [°C] (b) Torque output of the engine at this condition. [N.m] (c) What is bmep at this condition? [kPa] * 1 Add file Submit Never submit passwords through Google Forms. This form was created inside of University of Basrah. Report Abuse Google Forms
Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 m/s. The nozzles are inclined at an angle of 16° to the plane of the wheel. The blade velocity coefficient is 0.72, calculate the blade efficiency, work done and also estimate the energy lost in the blades as; m° (- .Take the blade angles at inlet and 2 2 outlet =25°. Ans. [76%,105 kw, 27.072 kW]
A double acting cylinder is hooked up in the regenerative circuit. The relief valvesetting is 105 bars and the pump flow is 0.0016m˄3 / s. If the regenerative and retractingspeed are equal to 0.25m/ s, find the piston and rod area and also load- carrying capacityfor the:a. Extending strokeb. Retracting stroke
Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d e
A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?
4- A centrifugal pump was tested for cavitation initiation. Total head was 40 m and flow rate were 0.06 m/s. Cavitation started when the total head at the suction side was 3 m. The atmospheric pressure was 760 mm Hg and the vapor pressure at this temperature was 2 kPa. It was proposed to install the pump where the atmospheric pressure is 700 mm Hg and the vapor pressure at the location temperature is 1 kPa. If the pump develops the same total head and flow, can the pump be fixed as the same height as the lab setup? What should be the new height.
A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%
Seven hundred gallons per minute of water are being discharged by a centrifugal pump 5 ft above the pump inlet. The inlet pressure is 4-in Hg above the atmospheric and the discharge pressure is 29 psia. If the pump has an 8-in diameter inlet and a 4-in diameter discharge, find the new flowrate if thr pump speed is doubled. Assume the pump input is 8Hp. A. 700 gpmB. 1050 gpmC. 1400 gpmD. 1750 gpm
An axial flow pump discharges water at the rate of 78 m³/min and runs at 550 rpm. The total head is 10 m. Assume blade velocity of 22 m/s, flow velocity of 4.5 m/s, hydraulic efficiency of 0.87, and overall pump efficiency of 0.83. Calculate Cr OP 3.1. The power delivered to the water, and power input The impeller hub diameter and tip diameter 3.2. 3.3. The inlet and outlet blade angles for the rotor 30 07:30 S
3. A centrifugal pump of 350 mm diameter running at 1000 r.p.m. devclops a hcad of 18 metres. The vanes are curved back at an angle of 30° to the langent at outlet. If the velocity of flow is constant at 2-4 m/s, find the manometric efficiency of the pump. (Ans. 76-4%)
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS