Example(1) Consider the water siphon shown in Fig. below. Assuming that Bernoulli's equation is valid, (a) find an expression for the velocity V2 exiting the siphon tube. (b) If the tube is 1 cm in diameter and z, = 60 cm, z, =25 cm, estimate the flow rate in m'/s. Estimate the pressure at point(3) if 23=90Lwm z =0---- -----Z2 V2 TY

Example(1) Consider the water siphon shown in Fig. below. Assuming that Bernoulli's equation is valid, (a) find an expression for the velocity V2 exiting the siphon tube. (b) If the tube is 1 cm in diameter and z, = 60 cm, z, =25 cm, estimate the flow rate in m'/s. Estimate the pressure at point(3) if 23=90Lwm z =0---- -----Z2 V2 TY

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pro er hydrant nozzle in Fig. 1 has inlet and outlet diameters, D₁ = 8 cm and D₂ 1.0 cm. Water at 20°C flows through the nozzle at 0.001 m³/s and exits to the atmosphere. The atmospheric pressure is 101.3 KPa. Neglect the weight of the piping and nozzle. Compute: a) The exit fluid velocity, V2, ( b) The inlet pressure, Pl c) The horizontal force which must be resisted by the = flange bolts S d) The moment acting on the flange neglect the weight of the hydrant and water 10 m 8 cm Fig. 1: Water hydrant 1
Example(1) Consider the water siphon shown in Fig. below. Assuming that Bernoulli's equation is valid, (a) find an expression for the velocity V2 exiting the siphon tube. (b) If the tube is 1 cm in diameter and z = 60 cm, z2 =25 cm, estimate the flow rate in m²/s. Estimate the pressure at point(3) if 23=90cw z =0---- V2 НОНЕWORК Estimate the pressure at point (3 ) if Z3= 90cm.
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
A) A 0.4 m diameter fan running at 970 rev min' is tested when the air temperature is 10 °C and the barometric pressure is 772 mm Hg and the volume flow rate Q=0.7 m s. Find the corresponding volume flow of a geometrically similar fan of 1 m diameter, running at 500 rev min at same conditions. Assume that the fan efficiency is unchanged. Ja
Using the figure depicted below, perform the following: (a) Calculate the minimum height h at which cavitation occurs. Indicate on the figure where the cavitation occurs. (b) Calculate the volume flowrate (in m³/s) if h = 25 cm. Be sure to state all assumptions. Note that section 2 opens to atmosphere. D1 = 5 cm h D2 = 10 cm Free Jet (1) 2 Water at 20°C
3. Theoretical Analysis: [With reference to the Bernoulli and Continuity equations, provide a theoretical analysis of how flowrate can be calculated for a level venturi tube. Label each equation in the theoretical analysis with a number. Explain the steps as per the start given below...] As applied to a pipeline, Bernoulli's equation can be stated as follows: P2 -++ Z1 P1 v? +Z2 (1) Pg 2g Pg 2g I. where the subscripts refer to stations 1 &2 respectively. In this case the elevation head is the same for both stations since the venturi tube is horizontal therefore the Z terms in the above equation can be omitted, giving: 二

G1/ In the fig.shown, the Flow rate Pipe (A) is equal ( QA = 25 Lit15), the diameter is equal ( DA = 75 mm, D, = De = Dc =30mm), and the velocity in Pipe (D) is equal (Uo=5 m/s), the relation between flow rate in in 6o mm, Pipe (B) and pipe (c) GB =3 Qc. Find the Value of '. Re, Qc, Qo. 2- UA, UB, Uc: Pe = 30 mm water Pc = 30mm imput QA = 25 2i+/sec OA= 75 mm = 6o mm input = A outPut = B, C, D accumulation = o.
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri
In the fig-Shown, the Flow rate Pipe (A) is equal ( QA= 25 Lit15), he diameter is equal ( DA = 75mm, Do 60mm, De = Dc =30 mm). and the velocity in Pipe (D) is equal ( 40=5m/s). the relation between flow rate in Pipe (B) and pipe (c) in %3D %3D PB =3 Qc. Find the Ualue of .. 2- UA, UB, Uc: Pe =30 mm water Pc = 30 mm imput QA = 25 2it/sec = 75 mm Po = 6omm input = A outPut = B, C, D accumu lation = o.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
338 B/s O 1: 56% E 3:01 Question: Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-1 6 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. (2 1