Explain how can the nanometer length scale affect the system structure and surface area by calculating the variation of the (surface area to volume ratio) for a 5-micometer long fiber (cylindrical shape) if the particle diameter changes gradually from 1 nm to 100 nm (i.e. 1, 10, 20, 30, .. , 100) and plot the variation of surface area to volume ratio versus particle diameter.

Explain how can the nanometer length scale affect the system structure and surface area by calculating the variation of the (surface area to volume ratio) for a 5-micometer long fiber (cylindrical shape) if the particle diameter changes gradually from 1 nm to 100 nm (i.e. 1, 10, 20, 30, .. , 100) and plot the variation of surface area to volume ratio versus particle diameter.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter93: Refractometry

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the following figure, which parameter of van Deemter equation is involved in these variations. Which curve of them would provide the best separation of analytes and at what linear velocity?
In normal phase liquid chromatography, the general elution problem can be solved by: using a more polar mobile phase using a less polar mobile phase using a mobile phase gradient from more to less polar using a mobile phase gradient from less to more polar
(c) Why calibration by area normalisation is used when assessing drug stability
03: Assume the diameter of carbon fiber is 7 um and the diameter of glass fiber is 16 µm. Determine the fiber volume fraction in (1) Square array of fiber packing and (2) Triangular array of fiber packing, for fiber spacing-to-fiber diameter ratios (s/d) of 1.0, 1.25, 1.5, 1.75, and 2.0. i. ii. iii. Find the fiber center-to-center spacing for the ratios. Plot the fiber volume fractions and the center-to-center/ diameter Ratios What is the theoretical maximum fiber volume fraction for each of the two composites? Are they dependent on the fiber type or diameter?
When the distribution coefficient increases, the extraction efficiency increases or decreases
In flotation, what would happen to the attachment and detachment between the bubble and the particle given the following conditions: 1.) The particle size is much larger than the bubble size2.) The particle size is much smaller than the bubble size3.) The particle size and bubble size have roughly the similar sizes Please answer both the effects on attachment and detachment
The sedimentation coefficient for a protein in solution is determined to be 4.3 S, and the diffusion coefficient to be 5.5x10-11 m2s-1 (vb = 0.74 mLg-1; density = 1.0 gmL-1; and viscosity = 1.0x10-3 Pas-1). Use this information to calculate the molar mass (kgmol-1) of the protein. Assume temperature of 298 K.
2. Consider the diffusion of oxygenthrough alow density polyethylene (LDPE) sheet 15 mm thick. The pressures of oxygen at the two faces are 2000 kPa and 150 kPa, which are maintained constant. Assuming conditions of steady state, what is the diffusion flux (in cm³ STP/ cm2-s) at 298 K?
What is the gravimetric factor if a weight of cl is to be determined from a weight of PbCl2?
Calculate and plot the Köhler curves for dry NaCl particles of diameters 40 nm and 100 nm respectively. Calculate the critical supersaturations. Which one will most easily form a cloud droplet? Use surface tension of water, full solubility and u = 2, T = 298K.
(c) Do you expect the diffusion coefficient typically to be higher for interstitial diffusion or for substitutional diffusion? There is more than one correct answer. One reason is sufficient. I encourage you to challenge yourself to think of two. (d) What relationship do you expect to find between the diffusion coefficient for substitutional diffusion and the equilibrium melting temperature?
The Debye radius in a solution with an ionic strength of 75.0 mol/m3 was determined to be 0.301 nm. a. If all factors remain constant, but an ionic strength of 15.0 mol/m3 is used instead of 75.0 mol/m3, calculate the Debye radius. b. Which condition is more favorable for particle-particle attachment?