Explain when we use sectional views and how they are made?

Q: Projections drawing?

A: Solution:   The Top, Front and Side view are shown below:

Q: Explain the yield phenomenon and yield strength by drawing graphics.

A:

Q: Define what is Two dimensional anisotropy ?

A: given: Define what is Two dimensional anisotropy ?

Q: What happens when a particle is subjected to both conservative and non conservative forces at the…

A: When a particle is subjected to both conservative and non-conservative force, the total mechanical…

Q: For symmetric and large circular section which pattern is preferred

A: Given: Symmetrical and large circular section To explain Which pattern required for Symmetrical and…

Q: please describe

A: In this figure tensile test for the ductile and brittle material was carried out.  We all know that…

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: What is a pictorial drawing? What are the different types of pictorial drawings?

A:

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: How can we analyze the effects of impact?

A: The impact loads are the loads that act for a minimal amount of time but cause severe stresses and…

Q: Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.

A: The corner radii of punch and die is very important in sheet metal drawing process because the radii…

Q: Tandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing…

A: Given question 1 question 2

Q: Describe, using sketches, the possible metal forming process that could have been used to produce…

A: The shown fig can be produced with the help of the extrusion process. The extrusion process may be…

Q: 7) Sometimes Drawing crimps are used in deep drawing process for producing complex shapes. Why?

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A shell of 100 mm diameter and 100 mm height with the corner radius of 0.4 mm is to be produced by…

A: Given:Shell diameter, d=100 mmHeight, h=100 mmcorner radius, r=0.4 mm

Q: )Which design do you recommend? and why?

A: A design should be chosen based on accessibility , ease of machining and logic. Therefore, the…

Q: How do you work with Sketch in SOLIDWORKS?

A: Given:- Solidworks software To find:- How to create a sketch and work in it

Q: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process.  (b)…

A: Corner radii: The corner radii is the curved corner of any shape as shown in the figure below.…

Q: Discuss traditional drawing and Computer-Aided Drawing

A:

Q: Describe how curves and surfaces are transformed. while discussing computer-generated art,

A: A curve is a collection of points that is indefinitely big. Aside from endpoints, every point has…

Q: When are the thin-walled tubes of the noncircular cross-section often used to construct?

A: Thin-walled tubes are the thickness of the tube is less than 1/20th  of the diameter of the tube.…

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Q: Describe the concepts behind principal components and dimensionality reduction.

A: given; Describe the concepts behind principal components and dimensionality reduction.

Q: Provide a precise definition of the cross-product. And give an explanation of how it relates to…

A: for solution refer below images.

Q: Why do the supports that resist a force, such as a pin, restrict displacement?

A: Supports are provided to make the best use of objects depends on the necessity.

Q: Hello. Would it be possible to include detailed explanations in every step? Thank you.

A: Given: Two springs are opposite to each other and by the energy stored in spring A is transferred by…

Q: How many types of impact are there?

A: There are two types of impacts: 1. Head on impact. 2. No head on impact.

Q: Explain the importance of lubrication in wire drawing

A: Wire drawing Wire drawing is the process in which metal is pulled out through die using tensile…

Q: Describe, using sketches, the possible metal forming process that could have been used to produce…

A: Given:

Q: Q-6: When do the "ears" appear in drawn cup, through cup drawing tests? * Your answer

A: 6. When do the "ears" appear in drawn cup, through cup drawing tests?       Note :- you have posted…

Q: what is Deep Drawing?

A:

Q: In the deep drawing of cups, blanks show a tendency to wrinkle up around the periphery (flange). The…

A: Explanation: Wrinkling is a type of defects which occurs in the deep drawing operation . Wrinkling…

Q: It is simple, help me to describe the part and write the steps of how to draw it in Solid Works

A: The assembly shown in the figure above is a fidget spinner. It is basically used as a toy. However,…

Q: What is “back-of-the-envelope calculations”?

A: An informal way of mathematical computing, which is performed on a small piece of paper like an…

Q: There are two types of scales in aerial photographs, mention and explain them briefly

A: There are two types of scale in aerial photographs: i) large scale photograph ii) small scale…

Q: Explain the difference between deep drawing and redrawing

A: Deep drawing Deep drawing is a process in which a sheet metal blank is drawn into the forming die…

Q: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process. (b)…

A: (a) Sheet metal drawing process This is a type of forming process in which metal in the form of…

Q: 1. In the manufacture of automotive-body panels from carbon-steel sheet, stretcher strains (Lueders…

A: Given question : How can stretcher strains be eliminated? How wrinkles in deep drawing operation can…

Q: Projections drawing؟ ?

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 5. An aluminium sheet blank is to be manufactured into the part shown in Figure 3. Discuss using…

A: Given Aluminium sheet blank To find Operations

Q: Properties of areas of common shapes.

A: The area of some the common shapes with their properties are as follows, Circle: The property of a…

Q: How we can measure shear modulus?

A: Shear modulus or modulus of rigidity can be found from the torsion test. As a result of the twisting…

Q: What is streamline?

A:

Q: Enumerate the steps taken in creating the objects.

A: Solution:

Q: Water is extracted from a 7mm nozzle on a semi-spherical panel where the distance between Qatar's…

A:

Q: How can machinery parts and pipeline welds be tested for flies without destroying them? name several…

A: In the non destructive testing process the voids, cracks, inclusion or cracks due to which a part in…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.