F8-6. Determine the state of stress at point A on the cross section of the pipe assembly at section a-a. 200 mm a 400 mm -20 mm A Section a-a F8-6 1500 N 1000 N

Q: Choose the right answer 1. The mean Nusselt number for fully developed laminar flow in a circular…

A:

Q: For the timber shape neglect friction and find 1-The dimension (b) if the allowable shear stress is…

A:

Q: 2/5 The position of a particle in millimeters is given by s = 27 – 12t + , where t is in seconds.…

A: Given, Position as a function of time = s = ( 27 - 12 t + t2 ) mm   Velocity function can be found…

Q: A Kaplan turbine working under a head of 81 5 m is dis- charging 295 m%/sec. of water at 75 R.P.M.…

A:

Q: The bending moment reaction at the fixed support (in N.M) is 200 N/m A |B 3 m 3 m

A:

Q: teel propeller for a windmill transmits 8.1 kW at 63.4 rpm. If the allowable shear stress in the…

A:

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

A:

Q: 5.) Does a refrigerator full of food consume more power if the room temperature is 200C than if it…

A: Coefficient of performance of the refrigerator is given by the following formula, COP=TL/TH-TL Here…

Q: If the oscillator in the above problem is released from rest at x = A when the clock is set to t= 0…

A: Given   Position x = A when time, t = 0 Find   Position and velocity at t = 2 sec   Time, t

Q: A hollow steel shaft with an outside diameter of 62 mm and a wall thickness of 6 mm is subjected to…

A:

Q: Determine the distance (in m) from Point O where the resultant acts 260 N 200 N 2 m 2 m 2 m

A:

Q: A cantilever beam of length L = 6 ft supports a uniform load of intensity q = 200 lb/ft and a…

A:

Q: boiling in a tank at 0.01387 bars. Which of the following tank wall temperatures are possible (check…

A: Ans: B is correct.

Q: The amount of heat is equal to the done work according to the: * conservation of energy law…

A: According to the law of conservation of energy,The amount of heat is equal to the work done. From…

Q: 8-58 Two parallel disks having diameters of 50 cm are separated by a distance of 12.5 cm and placed…

A: Given               Diameter, d = 50 cm        Temperature, T1 = 1000 K…

Q: The logarithmic decrement of damping of a tuning fork oscillating with a frequency 1,1 Hz is 5.…

A: Given, Frequency of oscillations = f = 1.1 Hz Logarithmic decrement = δ = 5   Let us say after t…

Q: Determine the couple moment acting on the beam. 10 kN 4 m B 1 m 3. '10 kN

A: Given is  To determine  couple moment acting on the beam

Q: : By using LRFD method, select a W10 shape for column GH shown in figure for the following data: W=…

A:

Q: Determine the couple moment acting on the beam. 10 kN 4 m 1 m B 1 m 10 kN

A: For the Given system  To determine  Couple moment acting on the beam

Q: lost in (30m) of this pipe is measured experimentally and found to be (533m). Calcne Water flow in…

A:

Q: Determine the x-coordinate of the centroid of the area below bounded by the line x=3, the x-axis and…

A:

Q: answer d and e

A:

Q: When the compressor and motor operate on the same shaft and are enclosed in a common casing is known…

A: This question is based on the concept of semi hermetic sealed compressor

Q: OUTCOME 2: Impul As an energy enginee in order to establish a The design specificat Net head,…

A:

Q: 1 The relative density of a fluid is 1.26 and its dynamic viscosity is 1.50 Pa.s. Calculate its (i)…

A:

Q: A mass weighing 20 Ib. stretches one spring 5 times as much as it stretches a second spring. The…

A: Given data Mass attached = 20 lbThe mass stretches one spring 5 times as much as it stretches a…

Q: 5. Calculate the necessary draft angle for a reinforcement rib located behind a 6mm wall thickness…

A: The draft is basically an angle which is proveded to the pattern which we want to cast by using the…

Q: A rigid, closed container contains water vapor. It is heated from a saturated liquid state at 200°C…

A:

Q: 2. Show which kind of the double-pipe heat exchanger exchange more heat between the hot and cold…

A:

Q: Good afternoon!  May I know where is the part of b) 4 mpa. Thank you!

A:

Q: 8. A 15-g bullet moving at 300 m/s passes through a 2.0cm thick sheet of foam plastic and emerges…

A: Mass, m= 15 g= 0.015 kg Initial velocity, u= 300 m/s Final velocity, v= 90 m/s Thickness of the…

Q: Determine the rectangular and polar moments of inertia of the shaded area about the axes shown.…

A:

Q: Engineering Drawing: Dimensions

A:

Q: A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm…

A:

Q: Assuming a minimum design factor = 2.00, Design the bolted cover of pressure vessel; determine the…

A:

Q: Q3) The damped vibration record of a spring-mass-dashpot system shows the following data. Amplitude…

A:

Q: motor body is 360 mm in diameter (outside) and 240 mm long. Its surface temperature should not…

A: The fin is thin and long enough so that heat loss from the tip is negligible. All the heat is…

Q: need answer within 20

A: Yes, it can be used in honing stick in single layer configuration.

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: The largest torque that can be applied safely at the upper end of the steel rod: Tmax = 319.07 lb•in

Q: The couple moment acting on the beam is 400 N 400 N 200 N 0.2 m 200 N -3m 2 m 300 N 300 N O 640 Nm O…

A:

Q: A cylindrical shape is with diameter of 1.2m and length of 1.2m. The top surface has an emissivity…

A:

Q: If the oscillator in the above problem is released from rest at x= A when the clock is set to t= 0…

A: Given   Position x = A when time, t = 0 Find   Position and velocity at t = 2 sec    Time, t

Q: Two plate are joint by three rivets of 15 mm diameter. What is the shear stress in the material if…

A: For solution refer below images.

Q: Initially, a closed system consists of 2 lb of water vapor at the temperature and volume of 300°F…

A: Neglecting the kinetic and potential energy,1st of thermodynamics written as.. Q=∆U+W Here ∆U=0 ,…

Q: F12-2. Determine the slope and deflection of end A of the cantilevered beam. E = 200 GPa and I =…

A:

Q: 17-6 The two identical boards are bolled tngether to form the beam. Determine the maximum alowable…

A: Given data:- shear force (V) = 50 kN shear strength of each nail = 15 kN find the spacing of nails.

Q: 5- What are the main components of DC-sputtering device with schematic?

A: Solution is attached below

Q: 3.8 If the velocity distribution for a 2D ideal flow is given by

A:

Q: . What is the bumper's damping coefficient (c) such that the sy amping ratio of ɛ =1.25, when the…

A:

Q: )واجب بتی .H.W F3-5. If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.