Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the sleeve. Referring to the maximum allowable stress in copper, find the safe load P in kips that can be applied to the bearing plate.

Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the sleeve. Referring to the maximum allowable stress in copper, find the safe load P in kips that can be applied to the bearing plate.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Related questions

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: Area of copper = 2 in2 Area of aluminium = 3 in2 Allowable stress of copper = 20 ksi Allowable…

Q: Question 4. A hollow steel tube 5 m long with external and internal diameters 100 mm and 80 mm…

A: GIVEN DATA LOAD P=150KN LENGTH L=5m OUTER DIA=100mm INNER DIA=80mm CHANGE IN LENGTH =6.4mm FOS=4

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: The T-section short column shown in figure 10.19 carries an eccentric load P of 100 kN at the…

A: Concept: Since the force applied on the column at location other than the centroid, two stresses be…

Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…

Q: An aluminum bar having a cross-sectional area of 160 mm?. It carries the axial loads at positions…

Q: Find the maximum stress induced in the following cases taking stress concentration into account: 1.…

Q: Question 3: Find the extension in mild steel wire of 10 mm in diameter and 1.6 m long, the wire is…

A: Given, Diameter of the steel wire = d = 10 mm Length of the wire = 1.6 m = 1600 mm Axial load on the…

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure…

A: When it is required to join two rods which are placed under the tensile load and a small amount of…

Q: P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

A: Given, σy-B = 60 MPaσy-CD = 100 MPaSF = 2t = 6 mm Consider below FBD for the given question:

Q: An eye bolt carries a tensile load of 20 kN. Find the size of the bolt , if the tensile stress is…

Q: Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Data given- N= 47 So Side of sqaure x = 10+ 47/100 = 10.47 in Thickness t = 1+47/100 = 1.47 in…

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N Cross-sectional area…

Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…

A: Given data: Applied force (F) = 3000 kN Diameter (d) = 0.3 m Need to determine the shear stress in…

Q: load of 200 KN. If the length of the bar is 2 m and E = 200 GPa. What will be the elongation of the…

Q: 1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: A tianium disk (roe 107 CPa, Poisson's ratio = 0,34) precisely 8 mm thick by 30 mm diameter is used…

Q: Problem 2. A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm…

Q: A composite section 2 m in length, consisting of a steel tube with outer diameter 24 mm and…

A: Given data: Calculate the inner diameter of the steel tube.

Q: A 51 mm diameter steel rod (E = 207 GPA) with pinned end conditions is to be subjected to an axail…

A: Given Diameter, d = 51 mm E = 207 GPa Find Maximum length, L

Q: A steel rod with a cross sectional area of 120mm2 is stretched between two fixed points. The tensile…

Q: A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

A: Given Diameter, d = 62 mm Length, L = 945 mm Young's modulus, E = 200…

Q: A solid round steel rod with Sy 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

A: Given Length, L = 945 mm Diameter, d = 62 mm Yield…

Q: (i) Calculate the normal stress o on the upper part of the post. (ii) If it is desired that the…

Q: A steel rod of 30 mm diameter is subjected to a 10 kN of axial load. The length of the steel rod is…

Q: 8000 lb 3000 lb 7000 lb 2000 lb 4' 5' 3' Fig. P-208 and P-209. up (73 208. An aluminum bar having a…

A: To find: The total deformation. Give: The Young's modulus is E=10×106 psi. The cross sectional area…

Q: Example 20.2. A hollow alloy tube 6 m long with external diameter of 50 mm and interna. diameter of…

Q: A bar under 66,000 psi stress is loaded by a 4000 pound load. What is the bar’s cross sectional…

A: Given data as per question Stress = 66,000 psi Load = 4000 pound

Q: A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the…

A: Given data Length of steel rod (L) = 10 m Axial load (P) = 10 kN diameter (d) = 40 mm E = 200 GPa…

Q: What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the…

Q: 2. Shown in Figure below, is a section through a balcony. The total uniform load of 600 kN is…

A: Calculated load in each rod.

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

A: Given:σb=90 MPaσs=120 MPa

Q: A two spring is connected in parallel attached to a single load. The maximum allowable stress is…

A: Given that, Allowable stress, σ=200 MPa,Spring 1, d=33 mm,n=18,R=120 mm,Spring 2,d=30 mm,n=20,R=100…

Q: Compare the maximum stress induced into a rectangular plate 100mm long, 50mm width and 10mm…

A: The formulae for stress would be the ration of load to cross section area. The given problem will…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress…

Q: Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction,…

A: Given data :- Length = 100 mm Width = 50 mm Thickness = 10 mm Tensile load = 10 KN

Q: Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially…

A: We know that , when a bolt is subjected to tensile load , Pt=σt×As=σt×πd24 where , Pt=tensile load…

Q: 8- A steel bar of diameter 1 cm and length of 10 cm is made of steel with E= 200 Gpa and yield…

A: To find: The maximum tensile force. Given: The diameter of steel bar is d=1 cm. The length of steel…

Q: The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile…

Q: 4. The bar below is subjected to an axial load of P. The safety factor against compressive failure…

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

Q: 1.7 The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given, Diameter of wooden post = d = 8 in Length of square concrete footing = L = 12 in Working…

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Q: Aluminum A = 400 mm Bronze A = 200 mm Problem 2: An aluminum rod is rigidly attached between a steel…

A: Given dataMaximum stress in steel σmaxs = 140MPaMaximum stress in aluminium σmaxa = 90MPaMaximum…

Q: wire, but an extremely big block. So, compute the maximum load (in Newton) a round wire of this…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than
the sleeve. Referring to the maximum allowable stress in copper, find the safe load P in kips that
can be applied to the bearing plate.
Bearing
plate
P
СОРРER
ALUMINUM
Area (in?)
E (psi)
2
3
17 x 106
10 x 106
0.005 in.
Allowable Stress (ksi) 20
10
10 in.
Соpper
- Aluminum
Figure 5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 Figure 1
The frame supports the distributed load shown. Determine the state of stress acting at point E. (Figure 1) Figure 4 kN/m D. -1.5 m 1.5 m- -3 m 3m BA 20 mm 60 mm 20 mm 5m < 1 of 1 D E 50 mm Determine the normal tensile stress at point E. Express your answer using three significant figures and include the appropriate units. OE= Submit Part B μA TE= Value 1 Request Answer Value Units ELECT moord Determine the shear stress at point E. Express your answer using three significant figures and include the appropriate units. ? Units ?
Calculate the elustic limit of the plate 10 plate 8X0 - S00 pounds of load material 6061 Aluminum - Determine whattypeof stress is acting at this point -calculate the magnitude of this stress
10/10 find the tensile stress in upper plate in section 3-3 5. 1 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 2) 300 mm 8 mm
The steel bar has the dimensions shown. (Figure 1) Figure 30 mm 24 mm- 20 mm co 60 mm r = 15 mm 1 of 1 Part A Determine the maximum axial force P that can be applied so as not to exceed an allowable tensile stress of allow = 160 MPa. Express your answer to three significant figures and include the appropriate units. P= Value Submit μA Provide Feedback 3 Request Answer Units ?
A spherical pressure vessel 300 mm in diameter has a uniform thickness of 6 mm. The vessel contain gas under pressure of 6000 kPa. If the ultimate tensile stress is 450 MPa, what is the factor safety with respect to tensile failure?
Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the sleeve. Find the safe load (P) that can be applied to the bearing plate. Identify the safe load in kips. Bearing plate СОРРER ALUMINUM Area (in?) Е (psi) 3 17 x 106 10 x 106 0.005 in. Allowable Stress (ksi) 20 10 10 in. Copper - Aluminum Figure 5
Bar (1) in Figure PP1.2-6 has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 30 ksi, determine the maximum load P that may be supported by the structure. Answer in kips rounded-off to 2 decimal n 6 ft B (1) Figure PP1.2-6 4 ft 5 OF 6 QUESTIONS REMAI
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ilonger than the tube of length L = 10.52 in. Find the maximum safe load P (in Ib with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.64 sq, in. area of aluminum = 3.04 sq, in. E of copper = 17022171 ksi E of aluminum = 10073078 ksi allowable stress for copper = 19926 ksi allowable stress for aluminum = 10407 ksi Bearing plate 0.005 in. Copper - Aluminum