Figure 5 shows the circuit diagram for a two-stage amplifier. You may assume that the parameters are B= 0.025 A/V², threshold voltage V: = 0.6 V, and VA = 10 V for each transistor, and Cgs is negligible small for both M1 and M2. All other values are shown beside the schematic. (a) What kind of configuration is used for the 2 stages amplifier? (b) What kind of amplifier is M1 part of ? and what about M2? (c) Calculate the DC IDs for Mi and M2.

Figure 5 shows the circuit diagram for a two-stage amplifier. You may assume that the parameters are B= 0.025 A/V², threshold voltage V: = 0.6 V, and VA = 10 V for each transistor, and Cgs is negligible small for both M1 and M2. All other values are shown beside the schematic. (a) What kind of configuration is used for the 2 stages amplifier? (b) What kind of amplifier is M1 part of ? and what about M2? (c) Calculate the DC IDs for Mi and M2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. Determine the voltage gain of the non-inverting op-amp with Rf-100k and R1=4.7k02. Calculate the output voltage if the input voltage is 200mV
Use the following circuit to design an oscillator of 5 kHz output. The amplifier used in this oscillator is multistage C.S. with source resistance amplifier. The design must be with minimum No. of stages. Use the following FET parameters Id=2mA, gm=2.5 ms and rds = 40kN. Use VDD = 24V L R Vo Vi
A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is O 2.5mV/pC O 1mV/pC O 1.5mV/pC O 4mV/pC
100 W at 60 V from a Specify the 2 percent. size. Design a buck-boost converter to supply a load of 30 V source. The output ripple must be no more than duty ratio, switching frequency, inductor size, and capacitor
Q5. What type of amplifier is shown below? LM324 Vcc Vo Ri Vee %3D Vi Rf
for the circuit if R = 5ohm, E = 20V and the cut-off (trigger) angle is 90 degrees; Draw the waveform of the source current Is, the output voltage VDC, and the output current Id Calculate the average value of output voltage VDC and output current Id.
A circuit consist of two cascaded opamp amplifiers, If the gain of first stage is 6.7 and the gain of the second stage is 3. Then the total voltage gain A, is
The screen of a CRT is 60 cm from the centre of the plates. The parallel deflecting plates are of length 2 cm and are 5 mm apart. It has anode voltage of 2400 V. The input is supplied deflecting plates through an amplifier with gain of 20. To get a deflection of 3 cm on screen the input voltage is
Q5.Consider the differential amplifier shown in Figure 5 with transistorparameters B=150, VBEO) = 0.7 V, and V. Design the circuit such that the Q-point values are Ic Ica 100μA and voi-vo2 1.2 V for v=v₂-0.0 +3 V VOI -3 V Figure 5.
In the forllowing circuit, determine the value of the minimum base current required for saturation given that: Vcc = 12 V, VLED = 1.5 V, VCE(sat) 0.5 V , R. = 200 2, B,c = 50 +Vcc Ic Rc VLED ON ON RB Vin VCE 1s OFF Select one: a. 0.5 mA b. 4 mA C. 6 mA d. 1 mA
Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 KO Vcc RB www Bpc = 50 20 kN Draw the output waveform for the circuit shown below
Vin -100m/100mV. 10kHz RI B10k RF 100k Vcc +12V U1 UA741 A RL 25k -12V Vee 1. What are the basic features of an OP-AMP? (6) 2. Basic op-amp connections include what? (10) 3. Simulate the circuit using Circuit maker and explain the different between A and B.