For a roof truss system of an industrial building, following data is givenSpan of truss = 6.0 mSpacing of truss = 3.0 m centre to centreInclination of roof 30°Spacing of purlins = 2.0 m centre to centreWind pressure = 1.5 kN/m²Roof coverage -A.C. sheets weighing 200 N/m2%3D%3DDesign:(i) channel section purlins.

Answered: Image /qna-images/answer/68d5fd5d-e6a1-4ed2-84c7-a1bfa24200e0.jpg

For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spacing of truss = 3.0 m centre to centre Inclination of roof = 30° %3D %3D Spacing of purlins 2.0 m centre to centre Wind pressure = 1.5 kN/m2 Roof coverage A.C. sheets weighing 200 N/m? %3D %3D - Design: (1) channel section purlins.

For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spacing of truss = 3.0 m centre to centre Inclination of roof = 30° %3D %3D Spacing of purlins 2.0 m centre to centre Wind pressure = 1.5 kN/m2 Roof coverage A.C. sheets weighing 200 N/m? %3D %3D - Design: (1) channel section purlins.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

FOR THE GIVEN PROPERTIES DESIGN d': 15 mm THE REINFORCEMENT OF : 400 mm b d = $80 mm fc = 33 MPa fy = 320 MPa Mu: 1 000 000 000 N mm A. USE B.USE OF NSCP 2001 NSCP 2015 BEAM THE BEAM 132 13 Gra mm of BELOW. #H 1606 210135 03 M 12437 P0122399/100mA 02338941 242
A composite bar is rigidly attached to the wall at A as shown, Axial loads are applied at the positions indicated. Which of the following most nearly gives the axial stress in member AB? Bronze E = 83 GPa $ 100 mm Steel E= 200 GPa O 80 mm 1,200 kN 900 kN A B 2.50 m 3 m; Select the correct response: 179.05 MPa 38.20 MPa 59.58 MPa 114.59 MPa
Figure 3 shows a truss where P = 40 kN and Q = 27 kN. The force reaction at A in the y-direction is FAy = 29 kN up and the force reaction at G in the y- direction is FGy = 38 KN up. In the question that folows, select ihe anawer that in choneat to the tre vale. What is the magnitude of the force in member KL in units of kN? O 38.7 O 58.7 52.0 453
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)
8:13 PM Tue 2 Mar •?n 32% A docs.google.com Q2 Q2: A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress g and maximum compressive stress gc. 15 N 20 N/m 40 mm 40 mm E 225 mm-- 200 mm mm 2.5m 0.5 m Option 1 Send me a copy of my responses.
Solve for joint @ A & C / AC
"messenger_media?thread_id%=D100002917920802&attachment_id%3891210971774069&message_id%3Dmid.%24CAAAA Question 3 For the truss shown, determine the forces in members (a) BD; and (b) BF. 4 m4 m4 m-4 m- A B C 6 m E F G H O00 20 kN 20 kN 20 kN A BD-40kN (C); BF-33.33kN (T)
Example 3 Estimate the steel reinforcement for the Column as Shown in figures below -010mm@10cm -0.40 m 0mm@20am 10rmma10om Ø 10 / 200 mm c/c 8 Ø 16 mm 410rmm@10cm -90° hook 135 135 hook frommo20cm $10mm@10cm b) 0.40 m 0.10m-
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
Two channels having the given properties shown is placed at a distance of 300 mm to back and is properly connected by a pair of lacings as shown. 305 mm Fy=248 mpa Properties of one channel A = 5690 mm² Ix = 67.3 x 10 mm* Assume K = 1.0 -260 mm- Lucre x= 17- d = 305 mm ly 2.12 x 10 mm x 17mm CIVIL ENGINEERING - STEEL DESIGN Determine the safe axial load in kN, that the column section could carry. Unsupported height of column is 6m.
12. Refer to figure 6. The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. = 20 mm a. 70.8 mm b. 75.2 mm c. 86.3 mm d. 80.5 mm e. none of the above FIGURE 6
What the Top and Bottom reinforcement at area A in X- direction ? (you can use the symbol Ф) * 6.0- -6.0 Aø12@200mm B BØ12@150mm CØ16@200mm Area A Dø12@250mm EØ16@250mm A Dimension in m Figure (1): Slab with beams 0.5- 3.5 3.5 4.5 (B)