For determining the centroid of the area marked below in blue, you could to consider two square segments: square A B C D and square D E F G. Given: a = 55 m, and b = 18 m, then the coordinate in x direction of the centroid of the following area ABCGFE will be: _________ m. Calculate your answer to 1 decimal place.

For determining the centroid of the area marked below in blue, you could to consider two square segments: square A B C D and square D E F G. Given: a = 55 m, and b = 18 m, then the coordinate in x direction of the centroid of the following area ABCGFE will be: _________ m. Calculate your answer to 1 decimal place.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 13R: Find the volume of the following: a. 5 cube b. 10 of 8 pipe

See similar textbooks

Similar questions

2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits of your ID for the missing length x mm. ID:88 The following table facilitates the calculations for the required data 5 mm 10 mm 3 mm 10 mm x mm
Q. 2 Find the pasition of centraid with respect to given X and Y akis af shaded portian in the following figure: 225
1- Determine the location y of the centroid C of the beam having the cross-sectional area shown 150 mm 150 mm • Examaly 20 mm 20 mm B 150 mm 150 mm 15 mm 10 mm -15 mm 83 m 10 mm The missing data is 83 mm NB: each student inputs the missing data (in red dashed-line). The missing data is the last two digits of your ID number. If your two last-digits number is smaller multiply by 10 (example if you get 19 →19x10 = 190)
Find the area of the following shape using the information provided. H-6 cm L-10 cm H-Sem
Compute the coordinates of the centroid (x, y) of the area shown. Also compute the area moment of intertia about the x' and y' axes with origin at the centroid. C a *b*a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 40 cm 23 сm 49 cm The x coordinate of the centroid is x cm. The coordinate of the centroid is y cm. The moment of inertia about the x' axis going through the centroid is I,' cm4. The moment of inertia about the y' axis going through the centroid is I," cm4.
4) Listen For the composite area shown in the image below, if the dimensions are a 38 mm, b = 212 mm, c = 292 mm, and b 134 mm, determine the coordinate y (in mm) for its centroid location, measured from the bottom x-axis. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. C Your Answer:
Find the volume of the following: a. 5 cube b. 10 of 8 pipe
Correct: Item B with radius 130mm. Show your COMPLETE solution in 3 decimal places. If W=789 then use it 789. If u dont understand then reject my question ask for information ok
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
Determine the centroid of the area of the shaded region shown in Figure. 50 mm 50 mm 150 mm 150 150 mm 50 mm Match each item to a choice: y Choices: : 150 : 98.5 : 107.19 : 107.19 : 86.2 : 60 : 80 : 50
Write the first trigonometric function in terms of the second for 0 in the given quadrant. tan(0), cos(0); 0 in Quadrant II tan(0) =
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 360.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.30 MN. pressure vessel W bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x10 X