For the bar shown in the figure, determine what the value of force Fc must be for the displacement at point C to be null. For calculation purposes, consider L1 = L2 = 2 m, E = 201 GPa, A = 180 mm?, p0 = 1000N/m, FB =1000 Also obtain the expressions and plot the axial displacements u(x), the resulting normals Nx (x) and normal stresses axx(x). EA = constant Po EA cte Fe Fc L, L2

For the bar shown in the figure, determine what the value of force Fc must be for the displacement at point C to be null. For calculation purposes, consider L1 = L2 = 2 m, E = 201 GPa, A = 180 mm?, p0 = 1000N/m, FB =1000 Also obtain the expressions and plot the axial displacements u(x), the resulting normals Nx (x) and normal stresses axx(x). EA = constant Po EA cte Fe Fc L, L2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

use the stiffness matrix method to find the displacement at node 1,2,3,4 K1= 8 N/mm K2= 12 N/mm K3= 20 N/mm K4= 15 N/mm K5= 35 N/mm P = 1000 N
A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 9 ksi. Given: ly=/₂=11.3 in 4 A=4.75 in² kmin = 0.983 in. Z 0.5 in. 1.43 in. с B ← 0.5 in. 5 in. 1.43 in. Y The largest permissible value of the moment Mo is 5 in. kip-in.
We need the following relationships in deriving the transverse shear stress formula, except? Select one: O a. My O = O b. Shear stresses on orthogonal planes are equal Oc. Shear force on a transverse plane equals the sum of the normal forces on two transverse planes of a beam d. dM =V dr
2. The bar is subjected to forces shown in the figure. If it has the original dimensions length 1 = 500 mm; height h = 20 cm; thickness t = 100 mm, determine the strains in all axes, new dimensions, and the change in the angle after the load is applied. E = 5.5(10⁹) Pa, v = 0.2 14 MPa 28 MPa 0
The rectangular cross-section beam in figure 3b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places. (show all work)
The beam shown in the figure has a roller support at A, a fixed support at C and an internal hinge at B. The lengths of segments AB and BC are a and b respectively. A uniformly distributed load, q, is applied between points B and C, and a concentrated load P acts at a distance a/2 from the support A. EI is constant. a/2 P for quin A B Figure 2: Beam with internal hinge Determine the expression for the elastic curve (v(x)) for segment AB using the method of integration. Use a = 2 m, b = 3 m, E = 70 GPa, I = 198 × 106 mm4, P = 10 kN and q = 2 kN/m.
A vertical tapered rod of length L has its diameter varying linearly from 'd' at lower end to D at the upper end which has fixed support. Young's modulus of the material is E. Show that the elongation of the rod at its lower end when subjected to a longitudinal force F is given by &= 4FL/ πdDE
7. The simply-supported beam of Figure 7 has flexural rigidity EI and is subjected to a distributed load that increases linearly from zero at the ends of the beam to a maximum value of wo per unit length at the center, x = L/2. Wo per unit length L /2 L/2 Figure 7 (i) Write down an expression defining the distributed load, w(x), in terms of discontinuity functions. (ii) Find the bending moment M(x) as a function of x, also in terms of discontinuity functions. (iii) State the boundary conditions that must be satisfied by the beam displacement, v(x). (iv) Find the displacement of the beam at x = L/2. the simply-supported beam of figure 7 has flexural rigidity El and is subjected to a distributed load that increases linearly from zero at the ends of the beam to a maximum value of wo per unit length at the center, x=L/2
Question 1 Refer to the given figure as shown. P= 70 kN Cross section Area: 50mm x 50mm Modulus of Elasticity: 70 GPa 2P S! 4 m 3 m EA = constant Determine the force in member BC in kN. Express your answer in nearest whole number. Indicate (-) if compression. Determine the unit stress in member AC. Express your answer in 2 decimal places. Neglect sign. Determine the horizontal displacement at joint C in mm. Express your answer in 1 decimal place. Neglect sign. Determine the vertical displacement at joint D in mm. Express your answer in 1 decimal place. Neglect sign.
Refer to the given figure as shown. P= 40 kN Cross section Area: 50mm x 50mm Modulus of Elasticity: 70 GPa P P 2P 4 m A 3 m EA = constant Determine the force in member BC in kN. Express your answer in nearest whole number. Indicate (-) if compression. Determine the unit stress in member AC. Express your answer in 2 decimal places. Neglect sign. Determine the horizontal displacement at joint C in mm. Express your answer in 1 decimal place. Neglect sign. Determine the vertical displacement at joint D in mm. Express your answer in 1 decimal place. Neglect sign.
The state of stress in a deformable body is shown in the figure. Consider transformation of the stress from the x-y coordinate system to the X-Y coordinate system. The angle 8, locating the X-axis, is assumed to be positive when measured from the x-axis in counter-clockwise direction. Y G₁ = 40 MPa 0xY Y 0 XY σ.. = 120 MPa = 50 MPa 30⁰ O = 35.6 MPa The absolute magnitude of the shear stress component Oxy (in MPa. round off to one decimal place) in x-y coordinate system is
Consider the truss shown in (Figure 1). AE is constant. Assume that AE is in kN. Use the principle of virtual work to solve this problem. Show Transcribed Text H B 2m 2m Show Transcribed Text Ac, = 30 kN 15| ΑΣΦ | 241 Submit Request Answer G vec 40 kN 2 m g Determine the vertical displacement of joint C measured downward. Express your answer in terms of A and E. Express the coefficients using three significant figures. Enter positive value if the displacement is downward and negative value if the displacement is upward. 30 kN 2 m ? 2 m m