i need the answer quickly Q1)For the circuit shown below, calculate: -1. The input impedances (Z,), (Z).2. the loaded output impedances (Z,). (Zof).3. The total voltage gain with (A) and without (A,) feedback connection.4. The output voltage (v.).$24 kn32 knVo10 mV24 knv, V 1 Ma1 Mn10 k680 n680 A{6 kn02)

We will do dc analysis to find out transconductance and then we will do ac analysis to calculate…

Answered: For the circuit shown below, calculate:…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is a typical value of open-loop, low-frequency gain of an op-arop circuit? How does this compare to the ideal value?
For the collector feedback configuration of Figure a. Determine re. b. Find Zi and Zo. c. Calculate Av. 12 V 3.9 k2 220 k2 V; o Z, B= 120 ro = 40 k2 Z;
e. f. a. An ideal feedback amplifier is given as block diagram. According to feedback topology do the required calculations and fill the blanks. Show your calculation steps as well. b. C. The type of feedback applied to this circuit is Forward direction transfer function is Feedback transfer function is d. Value of open loop gain of the amplifier is. Value of feedback loop gain of the amplifier is.. 1 Considering that V₁ = 100mV; V=99mV; V, = 5V. Show all the required calculations. Value of closed loop gain of the amplifier is ... amplification. ..amplification. ..(Calculate and write with unit) ..(Calculate and write with unit) ..(Calculate and write with unit)
4. The circuit uses current- (or shunt-) feedback bias. The Si transistor has ICEO = 0, VCEsat =0, and B= 100. If RC = 2k and VCC =12V, size RF for ideal maximum symmetrical swing (that is, location of the quiescent point such that VCEQ =VCC/2). +V cc RC Cc Rs RL VL Cc R. R
2. For the Feedback Amplifier circuit shown in Figure 4, determine the following: a. Identify the type of sampling and mixing for the amplifier. b. Calculate the feedback factor for the amplifier. c. Draw the small signal equivalent circuit for the amplifier with no feedback and calculate the voltage gain without any feedback. d. Calculate the voltage gain with feedback. e. Calculate input and output resistances of the amplifier with feedback. B=100; 2=2.5k12. No DC Calculations necessary. +15V IK: Vs look TON't 27k fig. lONf -15V 4. €2.5k ZONE lk $250 Yout F₂0 =20NF lok
In the amplifier circuit seen in the figure below;a) input impedance (ZI),b) calculate the average frequency zone voltage gain AV=(V0 / Vi)
1. TRUE OR FALSE . (a) The closed loop gain of a negative feedback amplifier is less than its open loop gain.(b) For a voltage amplifier, the input impedance and output impedance should be very high.(c) For a transconductance amplifier, the input impedance should be very low and the output impedance shouldbe very high.(d) For a voltage amplifier, the output voltage on the load decreases if the output impedance of the amplifierincreases.(e) For a current amplifier, the output current on the load decreases if the output impedance of the amplifierincreases.
1. Consider an inverting operational amplifier circuit with Ri = 10kohms and Rf = 50kohms. a. Determine the closed loop voltage gain b. Determine the input impedance of the circuit. c. Determine the ideal output impedance of the circuit.
Use the PAL with a feedback portion below to implement the following function:
2-) The AC equivalent of a feedback amplifier circuit is given in the figure on the right. (Hfe100, Va = ∞, Ic1 = 15 mA, Ic2 = 5mA and Ic3 = 5 mA) a) State the type of feedback used in the circuit, explaining the reason. b) Draw the small signal equivalent of the amplifier circuit. c) Calculate the value of β for the feedback by drawing the β circuit. d) Find the Avf = Vo / Vs closed loop gain of this circuit. e) Find the Rif and Rof values.
What is intrinsic standoff ratio?
solve a,b and c please. a. Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET? b. Compare inverting and non-inverting amplifier? c. calculate the closed loop gain of the circuit diagram given below.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

For the circuit shown below, calculate: - 1. The input impedances (Z,), (Z). 2. the loaded output impedances (Z,). (Z.s). 3. The total voltage gain with (A) and without (A,) feedback connection. 4. The output voltage (v.). 24V $24 kn 10 mV 24 k v, V 1 Ma 1 Mn 10 k 680 n 680 n