For the mechanism shown, the angular velocity of link AB (WAB) is constant and known, and the ang ular velocity of link BC (WBC) is provided so you don't have to calculate it. The dimensions and parameters you are to use are provided in the table below. Signs denote+ for CCW and - for CW. Determine the acceleration vector of point C-using the three diagram method (you must draw and properly label the three diagrams of link BC as part of your answer).

For the mechanism shown, the angular velocity of link AB (WAB) is constant and known, and the ang ular velocity of link BC (WBC) is provided so you don't have to calculate it. The dimensions and parameters you are to use are provided in the table below. Signs denote+ for CCW and - for CW. Determine the acceleration vector of point C-using the three diagram method (you must draw and properly label the three diagrams of link BC as part of your answer).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the acceleration of points A and B also the angular accelerations of links 3 and 4 using Relative Acceleration Method. Input link has constant angular velocity. Note that the drawing is not in scale. @2=1 rad/s 02 O 2 30° A 3 B (0) 04 02A=4" AB=7" 0204=9" 04B-8"
(10 points) Crank_Slider2 a WOP, dop Known values: a 0.38 m 3.4 m 20° 68° Problem Statement: Crank OP rotates about fixed axis O, causing slider Q to oscillate in a horizontal track. At the instant depicted, the angular velocity of crank OP is 4 rad/s and its angular acceleration is 6 rad/s?. For that instant, determine the following. The velocity vector of pin P: i+ 1.4283 m/s -0.5199 m/s The angular velocity of rod PQ: The velocity vector of slider Q: The acceleration vector of pin P: 计 The angular acceleration of rod PQ: The acceleration vector of slider Q: i+
Draw a six-bar linkage mechanism used for holding an industrial stirrer. Points A, B, and E are on a straight line on link 2. Points B, C, and G are on a straight line on link 3. The input link 2 rotates with a constant angular velocity a of 3 rad/s (cw) at the instant. O2=0 (a) Complete the acceleration polygon according to the drawing scale given, and find the angular accelerations Oy, 04, as, and as of links 3, 4, 5, and 6, and the acceleration Ap of point F. The position of link 2 is given as input. Write down the vector loop equations of the linkage for analytical position analysis and identify the unknowns in the equations. Note: Round off all your answers to two decimal places. Dimensions: AB= 40.00 mm BE = 20.00 mm BC = 33.54 mm CG= 33.54 mm CD = 18.03 mm EF = 43.00 mm FG = 29.15 mm
Find the instantaneous velocity of slider F, in mm/s using relative velocity method. The crank AB rotates in uniform angular speed of 150 rpm in counter clockwise direction. AB = 50 mm, BD = 400 mm, DC = 150 mm, CE = 100 mm, EF = 95 mm, DC and CE are perpendicular. Draw in appropriate scale.USE GRAPHICAL APPROACH (AutoCad)
An L-shaped bar ABC has known velocity v and acceleration a, at point A and known ang ular velocity WABC and angular acceleration a ABC- The dimensions and parameters you are to use are provided in the table below. Signs denote + for CCW,- for CW, + for right, and- for left. B Determine the acceleration vector in terms of unit vectors for point C at this instant using vector math. LAB LBC Units in in A-F 7.5 5.0 LBC LAB LAG Ө WABC ABC deg rad/s rad/s 33 3.5 21 VA in/s 13.0 WABC ABC aA in/s² 24.0 a VA
The landing gear of an aircraft is the important mechanism retractable. At the instant shown in Figure 1,the crank AB on the small aircraft landing gear mechanism rotates counter clockwise at 15 rpm and accelerates at 4 rad/s². 1.Draw the displacement diagram to a scale 2.Use the relative acceleration method to graphically determine the linear velocity at point E 3.Determine the angular acceleration of the link DC
Find the instantaneous velocity of slider F, in mm/s using relative velocity method. The crank AB rotates in uniform angular speed of 150 rpm in counter clockwise direction. AB = 50 mm, BD = 400 mm, DC = 150 mm, CE = 100 mm, EF = 95 mm, DC and CE are perpendicular. Draw in appropriate scale. USING THE GRAPHICAL APPROACH (AutoCad)
Determine the velocity of slider C (link 4) and the velocity of slider B (link 5) assuming link 2 is rotating CW at 500 rotations per hour CCW. Assume all measurements or dimensions provided are in cm. All diagrams are to scale with the indicated lengths/coordinates. Please show your work. Use the velocity polygon method to solve. Thank you!
Find the velocity of point B and angular velocity in link 3 using relative analysis and polygon method. Note the drawing is not in scale. B 02 @2=1 rad/s 2 30° A 1 3 4 04 02A=4" AB=7" 0204-=9" 04B=8"
Answer using GRAPHICAL METHOD. Make a representation of the following vector quantities a. A velocity of 20m/s north b. A force of 2000 dynes 45° east of south c. An acceleration of 5m/s2 at 200° d. A displacement of 14m 100° from +x-axis e. A force of 250N at 60° clockwise +x-axis
The figure applies to the next questions. There is a body segment with up to three forces applied: proximal, distal, and external. In the coordinate system shown, the acceleration is [1, O, 0] m/s2, and the angular acceleration is 1 rad/s2 about the z axis. The mass is 1 kg, and the moment of inertia is 1 kg-m2. The proximal force is [0, 1, 0] N, and the proximal moment is 0 N-m. The grid has equal spacing 1 cm. 1 cm proximal COM distal If inverse dynamics is performed in the proximal-to-distal direction and, what is the reaction force exerted by this body segment on the distal body segment? A) [1; 0; 0] N B) [0; 1; 0] N C) [-1; 1; 0] N D) [2; 0; 0] N
actuating limb angular position is given as 812= 60° and the speed of the mechanism is given as é12= 50 rad/s. Do the following operations respectively. Kinematic diagram and limb dimensions are given below, in the arm slide mechanism, the a-Write the Vector Closure Equation into scalar form. b-Find S13, 014 by position analysis. C-Find Sı3Ö14 by analyzing velocity. A9A = r2 = 0.2 m A,Bo = r = 0.5 m 012 = 60° 012 = 50 rad/s S13 014 Bo 012 ri A0