For the Pratt bridge truss and loading shown, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 5.87 in?. В D F 12 ft E G - 9 ft 9 ft→-9 ft→9 ft- 80 kips 80 kips s0 kips Figure (6) Ans. (GBE= 58.73 MPa)

For the Pratt bridge truss and loading shown, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 5.87 in?. В D F 12 ft E G - 9 ft 9 ft→-9 ft→9 ft- 80 kips 80 kips s0 kips Figure (6) Ans. (GBE= 58.73 MPa)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The truss shown consists of wooden members. Knowing that each member has a 75 x 75 mm. square…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as show: Determine the…

Q: Refer the beam shown with cross section of thickness, t= 15 mm. If F = 84 kN and a = 150 mm, F 2a…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 8 mm².…

A: Given data w = 4.5 KN/m L = 4.75 m C/s area of rod 1 (A1) = 8 mm2 C/s area of rod 2 (A2) = 15 mm2…

Q: Determine the shear stress on the a-a plane. 45 MPa 30° a (а) -10.5 МРа (b) 10.5 MPа (c) -50.3 МРа…

A: Shear stress on plane a-a is given by ζxy'=σy-σx2sin2θ+ζxycos2θwhere θ=angle of inclination of…

Q: Given the beam shown with computedreactions and a cross section. 1. Draw the shear and moment…

A: As per bartleby guidelines, experts are allowed to solve only first three parts . Those are solved…

Q: A simple pin-connected truss is loaded and supported as shown in Figure P1.12. The load P is 200 kN.…

A: Overall equilibrium : ∑Fy=Dy-p=0Dy=p=200 KN∑My=Pa+Bac=0Ba=-Pac=P×126=-2P=-400…

Q: Two chords AB and BC are joined at Band support a load W as shown in Figure 3.3-8. A 30% 45° W…

Q: 3. The aluminum shaft, composed of three segments is fastened to rigid supports as A and D.…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that P 5…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 8 mm².…

Q: If P= 8.571 kN, Determine the stress in member CE assuming that the area in steel is 24 mm². 1.4 m D…

A: Determine the stress in member CE

Q: 1. The lap joint in Figure 1 is connected by three-20 mm diameter rivets. Assuming at the axial load…

A: Given data in question Load Diameter To find out Shear stress Bearing stress Maximum average…

Q: Problem 5.9 A solid steel bar has a cross section of side b and is supported as shown. Knowing that…

A: To Determine Depth of the beam, b

Q: I jp. sin. 05 in. B. 3 kip A9 kip 8 kip Lc-2 kip

Q: Problem 23.4. A hook carries a load of 7.5 kNand the load line is at a distance of 20 mm from the…

A: Here we will use the concept of bending of curved bars to calculate the value of stresses. Given…

Q: 3: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A: Given data dAB = 1.25 in dBC = 0.75 in P = 10 kips

Q: 000 N is applied to the bell crank shown. Determine: neter of rod CD if the allowable normal stress…

A: According to given data P= 1000 NTo find the required diameter of rod CD at 50 MPa allowable normal…

Q: Q.No.3: Determine the ACI design moment capacity of the beam shown in the Figure 2 if the fc' =4000…

A: The compressive strength of the concrete is f'c=4000 psi. The yield strength of the concrete is…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm², Est…

Q: Before the 400 kN load is applied, the rigid platform rests on two steel bara, each of cross…

Q: Q1. The structure shown consists of a S18 x 70 rolled-steel beam AB and two short members welded…

A: Finding out SFD and BMD of beam and maximum normal stress.

Q: .B + sodb 30 lb CROSS. SECTION

A: Normal stress: it is defined as the stress that is induced when the member is loaded by axial force.…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 9 mm2.…

Q: Q3 Figure 3 shows a steel shaft of length L = 1.8 m and diameter d = 27 mm that carries a…

A: Solution:- We know that, the equation of torsion is, TJ=τr=G.θL Let assume, x=1, then τ=255×11800τ =…

Q: Question 2) In the system given in the figure, a distributed load of w=85 kN/m acts on the rod AB of…

Q: Determine the combined stress at the outer edges AA and BB for a given short compression member as…

A: For eccentrically loaded members the combined stresses is calculate by -…

Q: The cross-sectional dimensions of the beam shown in the figure are a -4.8 in., b = 6 in., d=4.0 in.,…

A: Given data: Mz=-4.2 kip-ft

Q: Situation: A steel band saw 20 mm wide and 0.6 mm thick, runs over pulleys of diameter d. Find the…

Q: Lesson 1: Simple Stress #1. The assembly shown below is pinned at A & Cand A&C are subjected to a…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast 1000 mm². Eat…

Q: Find the shear stress on the inside and outside of the hollow pipe shown, and the total angle of…

A: Given T = 3500N-m Outside dia = 10.4 cm Inside diameter = 7.6 cm G = 7500 MPa L = 3m

Q: Compute the maximum shearing stress in MPa developed in the figure. (Round your answer to 2 decimal…

Q: Question 2) In the system given in the figure, a distributed load of w=36 kN/m acts on the rod AB of…

Q: 1. The lap joint shown in the figure is fastened by four 4-in.-diameter rivets. Calculate the…

Q: own below is 500 mm². 4. 3 m 3 m 3 m Determine the load P that will not (ceed a stress of 100 MPa in…

A: First find the reactions at the supports And then find the internal force in each member using…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

Q: are used to support a Arad Nadhom Shub H.W. 4: The two bars shown in Figure 2 load P. When unloaded,…

A: Given a=11ft b=6ft h=8ft When unloaded,B(0,0) When loaded,B(0.35,0.60) To find strain in each bar

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the…

Q: The crane hook carries a load of 24 kN and the section at P-Q is rectangular as shown in the figure.…

Q: A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Stress at A = 1.75N/mm2

Q: Question 2) In the system given in the figure, a distributed load of w = 88 kN / m affects the AB…

A: From above diagram : σm *(π*d24) = Tm (π*d*t) σm = allowable normal stress Tm = allowable shear…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 12 mm2.…

Q: is three times larger than in steel shaft. Q1) For the section shown aside, if the bending stress at…

Q: 3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a…

A: Given :

Q: E Expert Q&A b. M N. D. The normal stress (kN) at the L point resulting from the P-1000 kN pressure…

A: Normal stress: The stress that is formed in the body due to the application of external axial forces…

Q: 10cm 2cm 2cm 4 16cm 2cm M-SkNm

Q: 3) Knowing that P = Q = 480 N, determine (a) the distance a for which the absolute value of the…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A: To Find :- maximum load P that can be applied keeping the stress in bar 1 limited to 19 ksi

Q: In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi. Ift= 1.9…

A: Given:- σ=3.5 ksiτ=1.1 ksit=1.9 inb=3.8 in

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

For the Pratt bridge truss and loading shown, determine the average normal stress in
member BE, knowing that the cross-sectional area of that member is 5.87 in?.
В
D
F
12 ft
H
E
G
9 ft 9 ft-→9 ft→9 ft-
80 kips
80 kips
80 kips
Figure (6)
Ans. (GBE= 58.73 MPa)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. Use E = 200 GPa B 60 kN 2 m 40 kN E F1m--1m--1 m--1m-
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all members is 800 mm². Note: You may use any method 3 m E -2 m 3 m 4 m 5 m 6 KN
Exercises: Determine the normal stress in each member of the truss structures. 1. All joints are ball-joints; bottom 3 joints are fixed to the floor. Material: Steel 4KN b a-b-2 cm SKN a. Y. 10100
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
3) Find a) the maximum stress in the shown member, b) the relative displacement between 8 and D (Ap) c) change in segment BC length. Aluminum Eat=70 GPa AAB = 58 mm² 9 kN Copper Equ= 126 GPa Asc = 77 mm² 450 mm B 16 kN 16 kN 300 mm- Steel E = 200 GPa Acp=39 mm² 8 kN 8 kN 400 mm D 7 kN
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm