For the simply supported steel beam shown, determine the mid-span deflection and slope at both ends if thebeam is fabricated from a W457 x 113 wide-flange section.Given:• L=7m• L₂ = 5.25 mF = 95 kN• q = 76 kN/m-L₂LFq Write an elastic curve equation valid for the entire beam in the following form:y(x) = [B₁x³ + B₂.25 +B3 < x-5.25 >³ + C₁ + С₂]Place the coordinate system origin (x = 0) at the left end of the beam. Give values for the missing terms, inthe units listed.B1B₂ =B3 =C₁ =C₂ ==number (rtol=0.01, atol=1e-05)number (rtol=1e-05, atol-0.001)number (rtol=0.01, atol=1e-05)number (rtol=0.01, atol=1e-05)number (rtol-0.01, atol=1e-05)Ymid =number (rtol=0.01, atol=1e-05)Yleft-end =Yright-end =kN ?kN/m²Determine the mid-span deflection and the slope at both ends.number (rtol=0.01, atol=1e-05)number (rtol=0.01, atol=1e-05)kN ?kN m² ?kN.mºmm0?0?41

For the simply supported steel beam shown, determine the mid-span deflection and slope at both ends if the beam is fabricated from a W457 x 113 wide-flange section. Given: • L=7m ● L₂ = 5.25 m • F = 95 kN q= 76 kN/m L2 L F q

For the simply supported steel beam shown, determine the mid-span deflection and slope at both ends if the beam is fabricated from a W457 x 113 wide-flange section. Given: • L=7m ● L₂ = 5.25 m • F = 95 kN q= 76 kN/m L2 L F q

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The elevator starts from rest at the first floor of the building. It can accelerate at 4.8 ft/s² and…

A: Given data Acceleration = 4.8ft/s2 Deceleration = 1 ft/s2 Find the total time to reach 40ft

Q: 3: A steel pole is used to hold a triangular banner as shown. At its base, there are 8 bolts spaced…

Q: What would the minimum static factor of safety be based on yielding?

Q: According to the Sign Convention in our textbook, the normal stress Txy in the stress element shown…

A: According to the sign convention, the normal stress τxy in the stress element is considered as a…

Q: The determinant of the Jacobian of an element for a specific point is found to be equal to…

A: This question is based on the concept of finite element analysis.

Q: The truck is traveling at 18 km/h when the trailer coupling at A fails. If the trailer has a mass of…

Q: • A reinforced concrete section has a width of 300 mm and depth of 500 mm. The tensile…

A: The tensile strength of steel is σys=250 MPa. The young modulus of steel is E=200 GPa. The yield…

Q: The anchor opposite is made of Cr-Ni steel. There elastic limit is 520 Mpa. What should be the…

Q: He Find the stress tensor after 45 CCW rotation about x-axis if the origin stresses tensor is G xyz…

Q: In a single-flash geothermal power plant, geothermal water enters the flash chamber (a throttling…

A: Consider that the steam is flowing in the steady-flow system state that is a controlled volume…

Q: A car travels along the circular curve of radius r = 294 ft. At the instant shown, its angular rate…

Q: show that the Helix curve (threaded spring) r (t) = (cost, sin t, t) is constant. Is it the same as…

A: According to the question we need to explain The Helix curve (threaded spring) r (t) = (cost, sin t,…

Q: why 0.6 x06 + 0.5x0.6x0.40 ??????? I don't understand this please help me to understand it

A: In the problem, it was given the volume fraction of fibres Vf = 0.6, which means that 60% of the…

Q: Q2: Find the reactions in A, B, and D. 8" 895 lb 3.7" B 3.7" A D 2.5'

A: Given: Find the reactions at A, B and D.

Q: 3. Find the forces, magnitude and character, in the indicated member using Method of Sections. 10k…

A: According to the given data A loading structure is given We need to find Force in member A

Q: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as…

Q: Nowadays it is very important to reduce one's carbon "footprint" (how much carbon we produce in our…

A: Given: Initial cost - $2200 Reduce energy bill by = $315 To find: (a) What is the annual IRR of this…

Q: 4.10- Methanol is burned in an engine with air at an equivalence ratio of $=0.75. Write the balanced…

A: Given: Equivalence ratio, ϕ= 0.75 Required: Balanced chemical equation Air - Fuel ratio

Q: 4-7- A fuel mixture consists of 20%. isooctane, 20%. triptane 20%. isodecane, and 40% toluene by…

A: A mixture contains (By moles), Isoctane = C8H18 (20%) tripane = C7H16 (20%) Isodecane = C10 H22…

Q: Draw the shear and moment diagrams for the compound supported beam A 3 m 3 kN/m B -3 m- C 5 kN 1.5 m…

A: To find out :- 1. Shear force Diagram 2. Bending Force Diagram

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: A projectile is fired with an initial velocity of VA= 10 m/s off the roof of the building. Determine…

Q: What happens to velocity when smoke lines converge or diverge? 2- If the air velocity increases…

A: This question is based on the concept of fluid mechanics.

Q: Juggles the clown stands on one end of a teeter-totter at rest on the ground. Bangles the clown…

A: mB=76kg hB=2.1m hj=3.5m We need to find The mass of the Juggles

Q: Determine the equivalent force of a single cylinder engine, and the dynamic amplitude at 200 rpm.…

A: The given information in the problem is shown in the following attached image:

Q: Draw sheer diagram and bending moment diagram.

Q: ard Carnot cycle operates between temperatures of 300 and 1100 K. The mini- pressure in the cycle is…

Q: The s-plane plot of the poles and zeros graphically portrays the character of the natural response…

A: The s-plane is a complex plane used in control systems engineering to analyze the stability and…

Q: Explain the terms lines of flow and stream lines when applied to fluid flow and deduce the…

A: Fluid flow: It is the motion of fluid due to unbalanced forces acting on the fluid. A fluid can be…

Q: As an engineer, conduct a research on the hot and cold water supply system of a building,…

A: I can provide you with a general overview of a typical hot and cold water supply system in a…

Q: The bent flat bar rotates about a fixed axis through point O with the instantaneous angular…

A: Given data: α=5 rad/s2α=-5k rad/s2ω=2 rad/sω=2k rad/s Solution: The position of point A with…

Q: Q 14.25: A glass jar which contains water is placed in the freezer. Once the water has frozen the…

Q: An amusement park ride consists of a car which is attached to the cable OA. The car rotates in a…

Q: Isn't the area of the circle equal to pi times the square of its radius?

A: Explanation: Since the diameter ( d ) of steel bar is given, area of the circle is in terms of…

Q: Cylinders 1 and 2 are glued as shown in the figure. The tensile strength of the glue is 24 MPa, its…

Q: A 4-node quadrilateral element of 2D elasticity, as shown below in physical coordinates, is…

Q: QUESTION 4 According to the Sign Convention in our textbook, the normal stress Txy in the stress…

A: Find the direction of shear stress

Q: Eight identical springs are placed side by side (in parallel, like the two springs in the figure),…

A: According to the given data If the Keq=1800N/m Eight springs are connected in the parallel We need…

Q: Determine the reverse voltage and reverse current for the diode for each diode models. Also, find…

A: To calculate 1.The reverse voltage and reverse current for diode 2.The voltage across the limiting…

Q: 4- A projectile is launched from point A with the initial conditions shown in the figure. Determine…

Q: 4. A refrigerating plant having R-12 as the working fluid, comprises three evaporators of 10 TR at…

A: DISCLAIMER FOR MULTIPLE Since you have asked multiple question, we will solve the first question for…

Q: If the characteristic equation is + 4x + 8x naturnal frequency Wn are ¢ = 1/√√2 and wn = 2√2 (= 2/√2…

Q: 3-42 Determine the indices for the directions in the cubic unit cell shown in Figure 3-40. X A B C 4…

A: Draw the given diagram of cubic unit cell.

Q: The link AB has an angular velocity of 3.9 rad/s. (Figure 1) Figure transcript Determine the…

Q: 1. Mention the major components of a PV system. 2. Differentiate between grid connected and…

A: These questions are based on the concept of photo voltaic cells or solar cells.

Q: A Carnot cycle used nitrogen. The heat added is 50Kg , the isentropic expansion ratio is 12 & the…

A: Given data: Q=50 kJr=12Tl=24°C Note: here the unit of heat added is given wrong, so took it as 50…

Q: 1-15. Analyze the flow between two plates of Fig. 1-15 by assuming the fluid is a de Wack power-law…

A: (a) Draw the given diagram of the flow.

Q: 16-13M The compression ratio of an Otto cycle is 8: 1. Before the compression stroke of the cycle…

Q: How many reaction force(s) does a roller support have? 00 01 O2 03

A: Explanation: Roller support is used in engineering to allow a structure that can move horizontally…

Q: A large thin rectangular plate is subjected to certain traction boundary conditions on its thin…

A: φ(x,y)=Ax4+Bx2y2+Cy2

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

For the simply supported steel beam shown, determine the mid-span deflection and slope at both ends if the
beam is fabricated from a W457 x 113 wide-flange section.
Given:
• L=7m
• L₂ = 5.25 m
F = 95 kN
• q = 76 kN/m
-L₂
L
F
q

Write an elastic curve equation valid for the entire beam in the following form:
y(x) = [B₁x³ + B₂.25 +B3 < x-5.25 >³ + C₁ + С₂]
Place the coordinate system origin (x = 0) at the left end of the beam. Give values for the missing terms, in
the units listed.
B1
B₂ =
B3 =
C₁ =
C₂ =
=
number (rtol=0.01, atol=1e-05)
number (rtol=1e-05, atol-0.001)
number (rtol=0.01, atol=1e-05)
number (rtol=0.01, atol=1e-05)
number (rtol-0.01, atol=1e-05)
Ymid =
number (rtol=0.01, atol=1e-05)
Yleft-end =
Yright-end =
kN ?
kN/m²
Determine the mid-span deflection and the slope at both ends.
number (rtol=0.01, atol=1e-05)
number (rtol=0.01, atol=1e-05)
kN ?
kN m² ?
kN.mº
mm
0
?
0
?
41

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Calculation

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the steel cantilevered beam shown, determine the minimum moment of inertia of the structural tee section, Imin if the deflection at the free end is limited to 1.2 in. -L2 Given: .L=19.6 ft • L₂ = 6.6 ft F = 1200 lb • q = 1.05 kip/ft Imin=-512.6 79 - ¹/2 |F L +4₂+ L2 H q a
Select the lightest W-shape standard steel beam equivalent to the built-up steel beam below which supports of M = 150 kN - m. -200 mm. 15 mm SECTION MODULUS 1 870 X 10³ mm³ 1 550 X 10³ mm³ 1 340 X 10³ mm³ 1 330 X 10³ mm³ 1 510 X 10³ mm³ 1 440 X 10³ mm³ 1 410 X 10³ mm³ 300 mm 30 mm 15 mm DESIGNATION W610 X 82 W530 X 74 W530 X 66 W410 X 75 W360 X 91 W310 X 97 W250 X 115 (Input the W-shaped steel beam here:
A simply supported beam of dimension 12 m x 45 mm x 65 mm. It carries a uniformly distributed load of 450 kN/m for entire span. Determine (a) Maximum stress due to bending and (b) Young's modulus of the material used for the beam, if it deflects 150 mm maximum at the mid of the span. Also find the maximum slope in the beam. (Enter only the values by referring the units given, Also upload your hand written answers in the link provided) Moment of inertia of the cross section of the beam in m4 : Young's modulus of the beam material in MPa is = Maximum bending stress due to bending in MPa is = The slope at the supports of beam in radians is
For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the beam at A, and (b) the deflection Vmidspan of the beam at midspan (i.e., x = 2.45 m). Assume a constant value of El = 1270 kN-m² for the beam; M₁ = 9 kN-m, wo = 19.8 kN/m, LAB = 1.1 m, LBc = 2.7 m. MA A Answer: (a) VA = (b) Vmid i LAB i Wo B LBC mm. mm.
Problem 2 Moment-Area Method: For the given beam below, answer the questions. El = constant: 5 kN 8 kN-m A В 6 m 6 m 6 m (b) (c) | Draw the Curvature Diagram of the beam. Mark all important values. Determine the slope at point A, 64, using the moment-area method. | Determine the deflection at point B, Ag, using the moment-area method.
Using either Virtual Method or Castigliano Theorem, compute the slope and deflection at point B of the steel beam. Use E = 200 GPa & I = 60 x 106 mm*. Support C is fixed-supported and A is free-end. 3 kN B C A 5 m- 5 m-
For the beam shown; 1. Determine the equations of slope and deflection. 2. Determine the slope and deflection at point 3m from point A. A Take: E = 210 GPa., I=208x10-6 m4 12 KN 12 KN.m -1m-1m- AB 6 KN/m 2m 12 KN/m diy 2m
Using either Virtual Method or Castigliano Theorem, compute the slope and deflection at point B of the steel beam. Use E = 200 GPa & I = 60 x 106 mm4. Support C is fixed-supported and A is free-end. 3 kN В C A -5 m- -5 m
Q8a. The beam section below is solid and homogenous and has the following dimensions: b1 = 65 mm (top flange width), b2 = 65 mm (bottom flange width) and b3 = 25 mm (web width). d1 = 175 mm (section depth), d2 = 25 mm (top flange depth) and d3= 30 mm (bottom flange depth). For the solid homogeneous beam section shown below, determine its centroid coordinate x relative to the origin (0, 0) of the x-y axes. Give your answer for x in millimetres (mm) to two decimal places. b1 ]]d2 b3 di [d3 b2 Answer:
For the beam shown, determine the following: 2. Slope and deflection at the free end. 20 kN/m 50 kN -2m- 40 kN 100 KN-m
The cantilever beam shown is subjected to a concentrated load of P=70800 lb. The cross-sectional dimensions and the moment of inertia of the W16x57 wide-flange shape are: d = 16.4 in. tw=0.430 in. by=7.12 in. ty=0.715 in. 1₂-758 in.4 Compute the value of the shear stress at point H, located at y = 4.8 in. below the centroidal xis. H Answer: Shear stress = psi
5. For the beam shown in the figure, determine the slope at A and B and the value of the maximum deflection. 150 lb 240 lb 0.3 k/ft -10 ft -8 ft- - 10 ft- E = 29,000 ksi | = 20 in