For the structures loaded as shown, calculate the support reactions at A and B. A is supported by a hinge and B by a roller in both structures. The triangular load is perpendicular to the diagonal beam. 4' 2' 6' 9500 N 1200 N/m 500 N/m Tinm 8 850 N/m 50

For the structures loaded as shown, calculate the support reactions at A and B. A is supported by a hinge and B by a roller in both structures. The triangular load is perpendicular to the diagonal beam. 4' 2' 6' 9500 N 1200 N/m 500 N/m Tinm 8 850 N/m 50

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Similar questions

10b The 9.75 m long beam is simply supported at A and B as shown below with a uniformly distributed load (UDL) between A and C of 4.75 kN/m and a concentrated point load of 12.50 kN at point D (i.e., midpoint between C & B). Determine the reaction force Rg acting at B in kilonewtons (kN). Assume the beam is weightless and give your answer in kilonewtons (kN) to 2 decimal places. 12.50 kN 4.75 kN/m 1.125 m A 7.50 m 2.25 m B Answer:
* Required For nos. 38-40, satisfy the conditions of the given problem below: The internal drag truss of the wing of a light airplane is subjected to the forces shown in Determine the force in figure 3. each member, and state if the members are in tension or compression. 38. Load on member BC * 1 point H 0.61 m 0.61 m- 0.61 m 356 N O A. 579.23 N (T) B. 579.32 (C) O C. 580.20 N(T) D. 580.20 N (C) 356 N 0.61 m -0.46 m- 267 N 178 N
Determine the reaction components at the roller support at B and the hinge support at C due to the applied load shown in this figure. 10 kips 4 -3 ft- Support at B, Rg = 6 kips vertically upward direction. Support at C, Re-25 kips makes an angle 0= -33.13° with respect to +X axis. mm B Support at C, Rc-20 kips makes an angle 0-43.13 with respect to + X axis. Support at B, Rg - 36 kips vertically downward direction. Support at C, Re 15 kips makes an angle 0- 63.13 with respect to + X axis. Support at B, -3 ft-
6. The beam shown carries vertical loads. Calculate the reaction at each support. Neglect the weight of the beam. 8000 lb 03. 3'-0" 3'-0" 12-0" w = 600 lb/ft L = 24'-0" 3500 lb 4'-0" 2'-0" B
In the given figure, support A is a roller and support B is a pin support. If P=15 kips, calculate the 1) vertical reaction at A, 2) vertical reaction at B, 3) horizontal reaction at B P 6 kips 6 kips В 6 ft – 3 ft 2 ft ' 2 ft
Calculate the support reactions at A and B for the loaded beam. 96 lb/ft B 2.1 5.7' 74 lb Answers Ax = Ib Ay Ib By Ib
Problem #1 (Sections) cos 10 kips 30 kips sin == 0.6 3. Calculate the forces in Members 'CD' GD', and 3-0 "GH'. 4-0 4-0 40 40
Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A truss of a power transmission line tower is shown. Given loading of L = 1.2 kN. 1.60 m -2.21 m- -2.97 m- -2.21 m- D All R F L L P 1.20 m L 1.20 m KN (Click to select) 0.60 m The portion of truss shown represents the upper part of a power transmission line tower. Determine the force in each of the members located above HUJ. State whether each member is in tension (7) or compression (C). The force in member AB (FAB) is KN (Click to select) The force in member AC (FAC) is The force in member DF (FDA) is The force in member EF (FER) is The force in member BD (FBD) is The force in member DE (FDE) is The force in member BE (FB) is The force in member BC (FBC) is The force in member CE (FCE) is The force in member CH (FCH) is The force in member EH (FEH) is The force in member EJ (FE) is KN (Click to select) V KN (Click to select) $0.60 m 10.60 m KN (Click to…
Requlred Informatlon A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of interest A (at the top). B (at the center), and C(midway between A and B). - 200 mm- 50 mm B 50 mm Cross section at wall where F= 2.2 kN NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Calculate the magnitudes of the stresses acting on the stress elements. Do not neglect transverse shear stress. The magnitude of stresses acting on the stress elements are as follows: At element A, MPa and TA= MPa At element B. OB- MPa and T8= MPа At element C. MPa and IC= MPa
QUESTION 2 A beam supports a variably distributed load as shown in Figure 2. Given a pin support at A, and a roller support at B and the length of a is 2.8 m, calculate the vertical support reactions (in unit of kN). Assume upward and rightward are 'positive' and include the sign as part of your answers. You must include all necessary free body diagrams and intermediate calculations in your work solution. w = Wo-kx² A B. am 4m RA : 数字 kN RBY= kN
Question 1 Precision Engineering Contractors was awarded a government contract to construct a bridge joining two neighboring communities. The bridge ABC is simply supported at A and B 2 m apart and carries a uniformly distributed load of 50 KN/m between A and B, together with a concentrated load of 25 KN on an overhang at C, 0.5 m from B. Make a neat sketch of this bridge and calculate the maximum deflection from point A using Macaulay's Method. Take EI = 21 MNm²
A new art exhibit featuring mobile works is going up in the Norwalk, CA area. One art work is shown in the figure below. A 105 N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached 3/5 from the bottom of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 7.5 N. 10 WALL FLOR (a) ( If one shoe is attached 1/7 of the way up the beam and another shoe is attached 5/8 of the way up the beam, with e, = 70.1° and e, 30.1°, what is the tension in the cable, in newtons? %3! %3D (b) What is the x-component of the force, in newtons, that the pivot exerts on the bottom of the beam? (c) O What is the y-component of the force, in newtons, that the pivot exerts on the bottom of the beam?