The short rectangular column shown belowis eccentrically-loaded. Determine theforces in each layer of steel correspondingto the case of tension controlled strain limit.State if the force in each layer iscompression or tension. Use fc'= 4000 psiand fy = 60,000 psi and assume a clearspacing between stirrups and extremeconcrete surface to be 1.5 in. all round. Theconcrete is a normal weight concrete.8 No. 10 barsNo. 4 tiese15 in.30 in

Answered: Image /qna-images/answer/9382b92f-a454-429b-9fca-d8c46d9b3825.jpg

Answered: forces in each layer of steel…

Engineering

Civil Engineering

forces in each layer of steel corresponding to the case of tension controlled strain limit.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
Question 8 1 p The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec=23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 TE 730 N12 ligs (fsv.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the concrete stresses in tension and compression of the reinforcement concrete beam shown in Figure 3. Compression concrete stress Choose ] Tension Concrete stress Choose]
dae 11.25 kips st steel ∙Alum in um A fully bonded aluminum Outer shell and Steel inner core bar is axially loaded. Find the ✓1.25 kips normal stress for the alum', num outer shell. Answer in ksi Given: EA = 11,000 ksi Al Est = 29,000 ks; XAL = 13.5 x 10-6 Y OF Xst = 6.5 x 10-6 1/F dAl = 1.0 in. dst = 0.25 in. AT = 65 °F
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 730 N12 ligs (fx.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Use the Transformed section approach considering the presence of steel. Calculate the concrete area and transformed steel area in both tension and compression shown in Figure 3. n=Es/Ec Ast=1232mm^2 Use n-1 for the transformed area to do the calculate. Unit: mm^2 with two decimal
ASAP DONT REJECT ME, I'LL GIVE UPVOTE THANK YOUU Solve the basic development lengths in tension for the following deformed bars embedded in normal-weight concrete. State if you have assumptions. (a) 12mm bar dia; 32 mm bar dia. fy = 41.4 MPa fy = 413.7 MPa (b) 44mm bar dia; 57 mm bar dia. f c = 28 MPa fy = 552 MPa
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly rigid and sits on a 15 in x 15 in x 4 foot high concrete block which is fixed at the base. The system supports an axial load of P. A. Determine the normal stress in the steel. B. Determine the normal stress in the concrete. C. How much did the entire system shorten (Hint: the plate is perfectly rigid so it does not deform-just pretend it isn't there.) 15 in. Concrete 4 ft. 15 in. 8 in. Top View 8 in. Given: P = 250 kips L = 12 ft. d₁= 1 in. d₂ = 4 in. Esteel = 30,000 ksi Econcrete = 4,000 ksi
Problem 4 The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity, G, is 3.7 × 106 psi for aluminum and 5.6 x 106 psi for brass, determine the maximum shear stress (a) in cylinder AB, (b) in cylinder BC. Aluminum - 12 in. + 1.5 in. B T = 12.5 kip - in. Brass- 18 in. 2.0 in.
5. The rod bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C and D. The allowable stresses are 125 MPa in steel, 70 MPa in the brass, and 85 MPa in the aluminum. Assume that the allowable stresses are the same for tension (T) and compression (C). (a) Determine the diameter required for the brass bar. (b) Determine the required diameter for the steel bar. (c) Determine the required diameter for the aluminum bar. Express your answer in millimeters. Steel Brass C Aluminum B A 100 kN 85 kN 200 kN 215 kN 0.5 m 0.5 m 0.5 m
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 15 kips, w = 4.0 kips/ft, LAB = 3.2 ft, LBC= 3.2 ft, and LcD = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. P LAB Answer: Omax B LBC ↓↓↓ C ksi W LCD X
The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.-