Formulate the overall reliability of LCD display unit that consist of a display, backlighting panel and a number of circuit board with the following setup. Please include the model diagram in your answer. i)An LCD panel with hardware failure rate, λ 1 ii)A backlighting board with 10 bulbs with individual bulb failure rate of λ 2 but still considered good with 2 bulbs failures iii)2 microprocessor boards A and B hooked up in parallel, each with total circuit board failure rate of λ 3

Formulate the overall reliability of LCD display unit that consist of a display, backlighting panel and a number of circuit board with the following setup. Please include the model diagram in your answer. i)An LCD panel with hardware failure rate, λ 1 ii)A backlighting board with 10 bulbs with individual bulb failure rate of λ 2 but still considered good with 2 bulbs failures iii)2 microprocessor boards A and B hooked up in parallel, each with total circuit board failure rate of λ 3

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

Consider 16 KBps 10 device interfaced to 64-bit CPU using DMA interface in cycle- stealing mode. DMA contains 4-bit count register. Machine-cycle is 2 ms. What are the percentages of block time and busy time of CPU respectively?
A common bus in a computer connects 16 source registers (each register is 32 bits) and one memory unit with word size of 32 bits also. If the bus is designed using multiplexers, answer the following: • What is the minimum number of multiplexers required? What is the minimum number of select lines each multiplexer has? If the bus is designed with three-state buffers and decoders, answer the following: • What is the minimum number of three-state buffers required? • What is the minimum number of decoders required? • What is the minimum size of each decode
Because of the large number of devices in today's PC D9aog chips, finned heat sinks are often used to maintain the golchip at an acceptable operating temperature. Two fin ad designs are to be evaluated, both of which have base (unfinned) area dimensions of 53 mm X 57 mm. The fins are of square cross section and fabricated from an extruded aluminum alloy with a thermal conductivity of 175 W/m K. Cooling air may be supplied at 25°C, and the maximum allowable chip temperature is 75°C. Other features of the design and operating conditions Determine which fin arrangement is superior. In your analysis, calculate the heat rate, efficiency, and effec tiveness of a single fin, as well as the total heat rate and overall efficiency of the array. Since real estate inside the computer enclosure is important, compare the total heat rate per unit volume for the two designs. are tabulated. Fin Dimensions Convection Coefficient L (mm) Fins in Array (W/m2 K) Cross Section Length Number of Design w x w…
Using multiple 4M × 8 RAM chips (see below) plus a decoder, construct the block diagram of a 16M × 16 RAM system. Design the system below. Be sure you label the memory system inputs, Addr, R/W, and MemSel, and the system’s outputs D0~D15. Also label bus widths, and inputs and outputs of any required decoders. Put a star on the chips containing memory location 0.
Assuming two 32Kbyte memory devices are to be used for external memory-mappeddata storage, provide a circuit diagram showing how the devices should be connectedto the 8051. You should assume each device has active low Chip-Enable, Read, Write,8-data pins, and 15 address pins.
2 Show the calculation that leads to the conclusion that the minimum PWM frequency that can be achieved on the Tiva C-Series Launchpad with processor clock frequency 20 MHz and the default (no prescale) for the PWM clock is about 160 Hz.
Among the following which statements are not TRUE? A small part of the area of a wafer contains the number of devices that can be placed on a single chip. Numbers of wafers are processed at the same time, active and passive components are fabricated on a single chip of silicon. Numbers of wafers are processed at the same time and eliminating the complete dies on the boundary of the wafer Chips are fabricated in batch and possibly are placed on a wafer that are depends upon the size of the wafer. In wafer shaping eliminating the incomplete dies on the boundary and the number of dies dependent upon the diameter of the wafer
It is almost difficult to find a happy medium between the performance of the processor, the memory, and the bus as a result of the fact that two of the most important variables are susceptible to continuous change. This is due to the fact that the variables are of such a kind. Because of these characteristics, it could be difficult to establish a balance that is appropriate for all of the various kinds of devices.
Using multiple 4M × 8 RAM chips (see below) plus a decoder, construct the block diagram of a 16M × 16 RAM system. Hint: 1 million = 2^20. Design the system below. Be sure you label the memory system inputs, Addr, R/W, and MemSel, and the system’s outputs D0~D15. Also label bus widths, and inputs and outputs of any required decoders. Put a star on the chips containing memory location 0.
Consider the following situation: In an 8088-based microprocessor, it is needed to interface with 6 LED devices: determine the minimum number of 8255 PPI-chips to interface the LEDs?
Suppose a computer system has a common bus system for 8 registers of 16 bits each.The bus is constructed with multiplexers.a. How many selection inputs are there in each multiplexer?b. What size of multiplexers are needed?c. How many multiplexers are there in the bus?d. Draw the block diagram for this computer common bus system design.
A timing diagram for Direct Memory Access (DMA) with clock synchronisation?