Gear A on the drive shaft of the outboard motor has a radius ra=9 in. and the meshed pinion gearB on the propeller shaft has a radius rg-53 in.The point P is located on the propeller's tip at a distance 4 in. from the neutral axis of thepropeller's shaft.نندPBAt the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = A. t2.0 rad.s2 where t is in seconds.what must be the value of A to have, while starting from rest, vp=24 in.s¹¹ in 6 seconds ?

given; rA=9inrB=53inr=4in =0.1016mangular acceleration(α)=A*t2 rad/s2velocity at point P(Vp)=24…

Gear A on the drive shaft of the outboard motor has a radius rÃ=9 in. and the meshed pinion gear B on the propeller shaft has a radius rg=53 in. The point P is located on the propeller's tip at a distance 4 in. from the neutral axis of the propeller's shaft. سب P B At the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = A.t 2.0 rad.s 2 where t is in seconds.

Gear A on the drive shaft of the outboard motor has a radius rÃ=9 in. and the meshed pinion gear B on the propeller shaft has a radius rg=53 in. The point P is located on the propeller's tip at a distance 4 in. from the neutral axis of the propeller's shaft. سب P B At the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = A.t 2.0 rad.s 2 where t is in seconds.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 2 For the mechanism, shown on the figure, Onc = const 5 s'. O4=BC D0,3 m, AB-0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body OA: d) linear velocity and acceleration of the pointA. 120 60°
The moments of inertia of the parts attached to the input shaft X of the compound gearbox is 0.019 kgm2 and that of the parts attached to the output shaft Y of the compound gear system is 0.1 kgm2. If input shaft X exerts a constant torque of 7.27 Nm and is geared to output shaft Y, calculate the following: 6.4. The gear ratio that gives the maximum angular acceleration of output shaft Y.6.5. The corresponding angular acceleration of each shaft.
PROBLEM 2 For the mechanism, shown on the figure, @nc = const=5s. O4-BC-0,3 m. AB 0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body O4: d) linear velocity and acceleration of the point 4. 120
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
(Use relative motion analysis): The planetary gear system is used in car transmissions. There is sun gear S, planet gears P and the ring gear R. By locking (fixing/grounding) certain gears you can have different gear ratios and car speeds. = c) If the output shaft is held fixed, i.e. WA 0, and the ring gear is rotated at WR 5 rad/s, find the angular velocity, wp of = the planet gears and ws the sun gear. ως d) What if the planet gears are held fixed, Wp = 0 ? Шр WR R P WS 80 mm 40 mm 40 mm A
Unlike the common V6 engine, Subaru engines contain pistons that are horizontally opposed (see Wikipedia for more info). Luckily for us, this also makes for an interesting dynamics problem! At the instant shown, the crank arm's angular velocity is waB = 2,000 rpm (rotating clockwise) and the angle 0 = 40° with respect to the horizontal. Length of bar AB is r1 = 3 in. and the length of bar BD is r2 = 8 in. a) Clearly define coordinate systems for each link and write transformation arrays for each. b) Compute the velocity of point B in ft/s. Express your answer in rectangular coordinates. [Ans. to Check: 33.66 i– 40.11 j ft/sec] c) Determine the magnitude of the speed of the piston P in ft/s. Note: all answers should be positive since we only want to know the magnitude of the speed, not the direction (the piston can only move in the horizontal direction). [Ans. to Check: 43.6 ft/s] r2 10 B
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
The dimensions of the various links of a mechanism, as shown in Fig. 3, are as follows: OA = 0.3 m: AB = 1 m: CD = 0.8 m; and AC = CB. If the crank OA rotates at 100 rpm. in the anticlockwise direction, find, for the given configuration: 1. velocity and acceleration of B and D: 2. angular acceleration of the links AB and CD. 45 0.6 m- Eig 3
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s Ccw. And all forces acting. D EA = 0.55" AB - 2.5" AC = 1.0" 0.75" CB = 1.75" CD - 2.05" C 4 E O B 3 °2 60
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .