Answer the questions based from the result Data and ResultsLoad Cycles toFatigue(Small Paper Clip)Load Cycles toFatigue(Big Paper Clip)plasticProceduresmetalControl – 90 degreesControl – 180 degreesAnnealingQuenchingTempering18208243912184250 Give three reasons why different paper clip may break at different number ofbends?Did the paperclip got more difficult to bend as the number of bends increase?Explain.

Because of the following factors, different paper clips may break with varying numbers of bends:…

Answered: Give three reasons why different paper…

Engineering

Mechanical Engineering

Give three reasons why different paper clip may bre bends? Did the paperclip got more difficult to bend as the m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

zain 10 2G 3G zain IQ Z Questions of Lectu... -> Questions of Lecture Five: Q1)) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3) yield strength and tensile strength 4) Modulus ofelasticity and the strain hardening Q2)) Fill the following blanks: 1)) Tensile tests are used to 3)) The most application tests of applied static stresses to which materials can be subjected are ---------, ---------, --------- 4)) Tensile stresses cause ---------, and compressive stresses ----------, while shear stresses ----------, of the material. 5)) Engineering stress-strain is important in ----------, while the true stress-strain is important in ---------- 6)) The unit of mechanical stress is --------- or ----------, while the unit of strain is n compression test, when specimen is compressed, its height is ---------, and its cross-sectional area is 8)) Compression is in contrast to the tensile, the compression test contributes to the ----------, in stress…
I tried 33.7oC and also 50.517oC but it still says it is incorrect (view attached screenshot). I appreciate your efforts, but unfortunately it says it is still wrong. Any more ideas of what the correct answer might be? I really want to understand how to solve this problem correctly. Thank you!
For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?
Question 2: (Power law and sizing function) A company that produces high efficiency Fraction Horsepower DC motors. Started four years ago by producing both of 0.20, and 0.35 HP motors at the cost of $15 and $20 for each respectively. At that time the relevant Cost Index was 115. The company is currently considering the production of a 0.5 Horsepower motor of a similar design, the current cost index is 150. 1. Estimate the cost of the 0.5 Horsepower motor using the power law and sizing function. (Hint: Determine the value of index m first) 2. Estimate the cost if the company adds a speed Reducer Head to the motor at the current cost of 6:00 dollars
THERM0DYNAMICS PR0BLEM
1. With 25% efficiency, how much work is produced by Q-in of 31076 J? (answer format: 0000 no units) 2. With the parameters given from the previous number, how much is Q-out? Answer format: 00000, no need for unit 3. With the parameters from the previous question, how much heat was wasted? answer format: 00000 no units pls help ill rate you
The following information is available for Edgar Corporation’s Material X. Annual Usage 12,600 units Working days per year 360 days Normal lead time 20 days The units of Material X are required evenly throughout the year. What is the reorder points? Assuming that occasionally, the company experiences delay in the delivery of Material X, such that the lead time reaches a maximum of 30 days, how many units of safety stocks should the company maintain and what is the reorder point? Show computation.
Dynamic
Unit 7: Dynamic Surfaces and Chains Essay Question :d Cains 333 D 11 M . 11233200 Multiple-Choice Questions What dynamic surfaces can be found in a classic SLR camera? A. Lens B. Shutter C. Aperture adjuster D. Film Which of the following material attributes may present a problem in dynamic surface designing? A. Hardness B. Elasticity C. Opacity D. Smoothness edu.curriculum@stratasys.com Examine the image below. What would you do to improve the nesting layout ad shorten print time? A. Print tall parts and short parts separately B. Rotate tall parts to shorten Z axis height and reduce height differences between two part types C. Align all 6 parts to one row to reduce print-head travel time Increase spacing between parts D.
MECT361 Mechatronics Components and Instrumentation 8.1. Why is it not possible to connect sensors such as thermocouples, strain gages, and accelerometers directly to a digital computer or microprocessor? PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
IL IOUJOICIICA RAGICated in the 2-Dirmensional views (Orthographic) is milimeters centimeters There is no way of teling meters 3. When yow stari investigating to salve technological problems the following Technologiool Process yes can be followed to find information: Compare exising products write o design brief perform practical tests both A and C plus collect data. 4.Jocolleci dota the folowing could be used as a resource: Sractical investigation and testing of oproduct A, Band C A speok to or inteniew people firnd infomclion irom any print medio 6. existing products will help technologists in 20
True or False a) “If the most conservative fatigue criterion were used for infinite life design, the first cycle yield check is not needed.” b) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress concentration factor higher than the stress concentration factor under static loading condition in design. c) It is easier to find the asymptotic value of fatigue strength as the endurance limit on the S-N curve for a brass alloy (Cu70Zn30) than that of endurance limit on the S-N curve for an AISI 1045 steel.