Given: F = 40 N e = 20 deg a = 30 mm b = 200 mm

Q: Determine the force in members AD, CD, and CE of the truss shown.

A: Let, FAD = force in member AD FCD = force in member CD FCE = force in member CE RBH = horizontal…

Q: If the radius of wire stretched by a lo= doubled then its Young's modulus (a) will be doubled (b)…

A: we know that Young modulus is equal to the ratio of stress and  the strainY=σεY=FA∆ll

Q: Conclusion about Hooke's Law

A: To conclude that what Hooke's Law state

Q: a) Differentiate axial load and eccentric load b) Explain the limit of eccentricity.

A:

Q: - For a rope code "20 6x25F-WSC 1960 U zS" it is given as Fmin = 279kN. Which of the following is…

A: Given rope code is, "20 6x25F-WSC 1960 U zS" It means that, Nominal size of the diameter of rope =…

Q: F D B E C VA 4

A:

Q: Example 2.3: Find the mobility or degree of freedom of the following mechanism. Fork joint Slider 2…

A: DOF(degree of freedom) = it is the minimum no of independent coordinate which allows the movement.…

Q: E material has inner m'K, the temperatu

A:

Q: The factor of safety for mechanical components that are subjected to fatigue loading should be based…

A: Factor of safety for mechanical components is the ratio of endurance limit stress to working stress…

Q: 4-The magnetie horce per meter on awire is measured to be only 55% of t Maki mum possible Value…

A: When the current is perpendicular to the magnetic field, the force will be maximum. Fmaxl=IB The…

Q: A D. E F

A: No

Q: What is the length of cable AB? A = 840 N 6 m Fc = = 420 N 3 m B 2 m 3 m 2 m

A: To find:-Length of the  cable   AB.

Q: 2- why generally the voltage is applied to the L.V. side ?

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: 3. Determine the FBD, size and properties of all cable styles and vertical styles of BC structures!…

A:

Q: A 3 3 B 100 N 3

A:

Q: vapor pressure of the target material is 2x10 torr).

A: Given data Chamber Pressure is between 2 x 10-4 torr and 2 x 10-6 torr Gap between target material…

Q: the place and the value of the maximum tem

A:

Q: Subject Date : الموافق 2x92-0 م 24 find divgrad df) 2 19 - موضوع التاريخ

A:

Q: Define and explain hookes law

A:

Q: Q4: Two components are to be connected by bolts. One of components is relatively thick and the…

A: Given:

Q: Degree of freedom using Gruebler's equation.

A: It is asked to find the degrees of freedom using the Grueblers equation

Q: B. what is the type of force in each one of the figures below depending on the contact? 2 00. Fpash…

A: Types of Forces acted at different Kinds.

Q: Briefly explain the following terms.                                       Mechanical Vibration.…

A: Hi and thanks for the question. Since you have asked questions with multiple sub parts, We will…

Q: If C=50 F, and a 24 V battery is connected across 'a' and b’, what is the charge Q shown in the…

A: The rate of change of flow of charge across a circuit or conductor is termed as current. It is…

Q: PV If A = T Enter the SI units for A using the base units only.

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: What type 0f stress is being experienced by the wires ab0ve?

A:

Q: D B cable C=60° w =30 kN

A: given:

Q: Part 1 is as follows: al Diameter (mm) Tolerance (mт- 6 - 7.5 + 0.045 8 –10 + 0.050 a diameter wire…

A: To Find :  The mean and standard deviation of the population of torsional shear stress  Given : The…

Q: Question 2 Calculate the current i1 if R1 = 7 Ohms, R2 = 6 Ohms. R3 = 3 Ohms, R4 = 8 Ohms, and Vs =…

A:

Q: if the value of spring index is 9 and the mean diameter of the spring is 24 mm, the spring wire…

A:

Q: erence between a point loa

A: Difference between point load  and distributed load

Q: 600 N 600 N -F 40° 405

A:

Q: Determine the force in members BD and CD of the truss shown.

A: For the given truss   To determine  forces in member BD and CD

Q: A stadium roof truss is loaded as shown. Determine the force in members AE, EF, and FJ.

A: Consider the cut section of the truss as shown in the figure below. Let all the forces in the cut…

Q: n and a current of 1000 A is being passe mm/min. (Use F 96500)

A:

Q: Meaning of 316 in E316T-1

A: Given data : E316T-1

Q: The transistor in Figure 4-19 has the following maximum ratings: Pp(ma)= 500 mW, VCEimax) 25 V, and…

A:

Q: m -1, n (Tm.n-1 + Tm-1,m) + 2 T m, n Ay

A:

Q: and thickness but different se explain meaning of the re meaning of the 2 explain

A: solution of above problem is below:

Q: e of freedom according to which of the following equation?

A: Given - Degree of freedom-2 Links-5 Binary Joints- 3 Higher pair- 4 To determine the satisfied…

Q: e shear and moment diagrams :

A: Solution for 3rd question given below

Q: shown below. A e large diamete

A:

Q: Briefly explain/define the following topics. Use drawings and equations if necessary. Galvanic…

A:

Q: The strength constant (C) is increased with increasing of نقطة واحل .temperature True False O

A: From the strain sensitivity equation Yf=Cε˙m Yf=Flow stress C=Strength constant ε˙=Strain rate…

Q: From the table below, what is the initial tension required for the spring in letter (D): Hooke's Law

A: Given   Force constant, k = 10 N/m         Elongation, x = 0.52 cm                              =…

Q: Represent the following with SI units having an appropriate prefix: 0.893kg

A: given: Represent the following with SI units having an appropriate prefix: 0.893kg

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.