Given: In the series R-L-C circuit; R1 = 150-Q, R2 = 750-N, XL1 = j 1250-Q, XL2 = j 300-0, Xc1 = -j 900-0, Xc2 = - j 250-0 and e(t) = 40 sin(200t) v. Find: a) total impedance b) total current in the ckt. c) voltage drop VR; Vc and V. d) total power and power factor j1250ehms 150ohms -1900ohms 750ohms ll 1300ohms -1250ohms

Given: In the series R-L-C circuit; R1 = 150-Q, R2 = 750-N, XL1 = j 1250-Q, XL2 = j 300-0, Xc1 = -j 900-0, Xc2 = - j 250-0 and e(t) = 40 sin(200t) v. Find: a) total impedance b) total current in the ckt. c) voltage drop VR; Vc and V. d) total power and power factor j1250ehms 150ohms -1900ohms 750ohms ll 1300ohms -1250ohms

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.20P: A circuit consists of two impedances, Z1=2030 and Z2=2560, in parallel, supplied by a source voltage...

See similar textbooks

Similar questions

Impedance of the circuit..
This is not a graded assignment. Its a mock exam. I need help with both parts of the question: my current apporach thinking is that. To find the maximum average power transfer to the load I know we would first find the Impedance values of all the components and than add them up and than finally find the conjugate of that value correct? But im not sure how to find Pmax than based on what i got for part 1. Some guidance here would be appreciated. Im also not sure if my part 1 is correct either so i would apperciate assitance on that question as well
Q2. For the circuit shown in figure (a), let the frequency is 1KHZ, and V1 = 20Vms, draw the following: 100uF C2 V1 1000UF R1 VSINE 2K A. Impedance diagram B. Voltages phasor diagram. C. Measure the voltage across R1, Vin, and the capacitors, C1, C2 us ng the oscillscope using PROTEUS software. D. Measure the current in the circuit using DMM E. From the above measurments verify your result.
(a) A potential divider is formed from two elements with impedances, Z₁ and Z2. Sketch the layout and write down the equation for the voltage gain.
2, Zs Z7 Solve for: Solve for: h.) S5 i.) P6 j.) Q7 Given: E = 1002 – 90 volts Z4 = 42450 Z1 = 1200 Z5 = 5453.13N Z2 = 2436.87N Z6 = 62 – 90N Z3 = 32 - 30N Z, = 72750
write all possible KCL and KVL equations. simplify all and in ascending order, with contsant at the right side of the equation.
Predict value portion, using source voltage of 3.05 and R1 = 49 ohms and R2 = 99.5 ohms “Using Kirchhoff’s parallel circuit law”
Consider the following circuit used to provide power for an induative RL load. The input voltage is V-100V and the load has a 50 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 40A and the required dv/dt is 40V/us. If the value of Ce is equal to 0.14uF, then the snubber losses are equal to: R. V. Select one: O a 5.4W O b. 7.4W 1.4W Od. 3.4W
Source Transformation method I=? V50ohm=? P50ohm=?
How can i set up a supernode equation for this diagram? Is the nodes between V1 a super node?
transform the circuit in phasor domain representation a) Determine the value of branch current, I1 and I2b) Determine the value of voltage across resistor, R1, R2 and R3c) Determine the value of voltage across capacitor, C1 and C2d) Determine the value of voltage across inductor, L.
For the circuit shown in figure.Find: Zi Zo Ai re