h y g(x) 2h X An engineering student has modelled a truncated cone in CAD software by rotating the coloured area about the x-axis. The y-coordinate can be described by the equation g(x) = +1 and the cup has constant x 6 kg density p = 800 The cone has dimensions h = 1 m and l = 6 m. m³ Determine the cone's radius of gyration about the x-axis.

h y g(x) 2h X An engineering student has modelled a truncated cone in CAD software by rotating the coloured area about the x-axis. The y-coordinate can be described by the equation g(x) = +1 and the cup has constant x 6 kg density p = 800 The cone has dimensions h = 1 m and l = 6 m. m³ Determine the cone's radius of gyration about the x-axis.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.38P: The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the...

See similar textbooks

Similar questions

Use numerical integration to compute the product of inertia of the region show with respect to the x- and y-axes.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Determine Ix and Iy for the plane region using integration.
Determine Ix for the triangular region shown.
Use integration to compute Ix and Iy for the parabola. Check your answers with the results for the half parabolic complement in Table 9.2.
Compute Ix and Iy for the region shown.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Set up and evaluate the integral that gives the volume of the solid formed by revolving the region about thexaxis. Step 1 From the figure consider the representative rectangle. The radius of the solid of revolution obtained by revolving the rectangle about the xacis is R(X) -y9- To find the volume of a solid of revolution with the-Select mathod, use the horizontal axis of revolution. Select disk shel Volume-VE
For a given non-symmetric area and origin, when plotting Mohr's Circle, a reference point doesn't lie on the circumference but is located at the average distance between Imax and Imin at (297, 0). This reference point is the center of Mohr's Circle must correspond to one of the two principal moments of inertia corresponds to an axis on the cross-section that is not principal O provides the radius of Mohr's Circle that is equal to 297 provides the diameter of Mohr's Circle that is equal to 297
A cube of side a is cut out of another cube of side b that has a uniform density, as shown in the figure. Express the center of mass FCMof the structure using ijk unit vector notation. Set the origin at the front bottom-left corner of the figure where the dashed lines intersect. 7CM= Question Credit: OpenStax University Physics v1 a b
For the area shown in the figure below, OAC is the area of a sector with center at C and radius OC=AC=4*sqrt(2)~5.657 units. This is part 1. Part 2 is the triangle COD. Part 3 is the triangle CAB. Determine the radius of gyration of area of composite OABCD about the y-axis [units^4].
A triangular plate is supported by a ball and socketat point A, a roller at point B, and a rope at point C. Thedimensions are given along the line of AB. Determine thereactions at all supports and report your answers in cartesianvector form. Free Body Diagram.