Hand draw the compaction curve and identify three points X, Y, and Z which represent the wet of optimum, optimum and dry of optimum conditions. Discuss how the saturated coefficient of permeability and the effective shear strength parameters differ for specimens tested with initial conditions of X, Y, and Z.

Hand draw the compaction curve and identify three points X, Y, and Z which represent the wet of optimum, optimum and dry of optimum conditions. Discuss how the saturated coefficient of permeability and the effective shear strength parameters differ for specimens tested with initial conditions of X, Y, and Z.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.10P

See similar textbooks

Similar questions

2- A three-axis compression test has been performed on the clay sample, which has been comprehensively and normally strengthened to a stress of 300 kPa and a specific volume of 200. The values of q and volumetric strain are measured at axial strain of 0, 2 and percent (rupture). The value of N is equal to 300 and Landa is equal to 0.2. Draw a diagram of all- round stress on the initial all-round stress in terms of slicing on the initial all-round stress:.
A soil specimen is subjected to a tri – axial test. The soil specimen is cohesionless. If the shear stress that causes failure is 300 kPa. and the normal stress at failure is only 500 kPa 5. Determine the angle of shearing resistance in degrees 6. Determine the angle that the failure plane measured from the major principal plane. 7. Determine the total axial stress in kPa at which failure is expected to occur.
3. In a drained tri-axial test, a specimen is confined under pressure and axially loaded until failure. The failure conditions of the specimen are analyzed for shear strength. What is the value of the minor principle stress? Half the value of the major principle stress Twice the value of the major principle stress . The same as the confining pressure The same as the cohesion value ● ● ●
Triaxial tests performed on samples of aeolin sand. The failure conditions in terms of effective stress are (ov, 0h) = (515, 100), (1250, 200), (3500, 400), and (5325, 800) kPa. Using (s, t) space, determine the cohesion and friction angle. What is the orientation of the major principal stress with respect to the failure plane? Determine this graphically.
2- A three-axis compression test on a clay sample that is comprehensive and normal up to a stress of 300 kPa and a specific volume of 2 Consolidated is done, The values of q and volumetric strain are measured at axial strain, 0, 2 and 10 percent (failure) . The value of N is equal to 3 and A is equal to 0.2. Graph of all-round stress on initial all-round stress Draw the initial all-round stress in terms of section
A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf
A cohesionless soil sample is subjected to a triaxial test. The critical state friction angle of the soil is 28 degrees and the normal effective at the failure is 200 kPa. Determine the critical state shear stress. Determine the plunger stress. Determine the cell pressure.
A CU triaxial compression test was performed on saturated sand at a cell pressure of 100 kPa. The ultimate deviator stress was 350 kPa and the pore pressure at the peak stress was 40 kPa (suction). Estimate the total and effective stress shear strength parameters.
A sample of dry sand is subjected to a tri- axial test. The angle of internal friction is 36.6°. The minor principal stress is 192 KPa. Compute the effective normal stress in KPa at the point where shear occurs at the failure plane.
A tri-axial compression test on a cohesive sample of cylindrical in shape, which fails along a plane making an angle of 60 degrees with the horizontal, yields the following effective stress. Compute the angle of internal friction. Compute the cohesion of the soil sample. Compute the shear stress (MN/m^2) at the rupture plane.
An undisturbed soil sample, 110 mm in diameter and 220 mm in height, was tested in atriaxial machine. The sample sheared under an additional axial load of 3.35 kN with avertical deformation of 21 mm. The failure plane was inclined at 50˚ to the horizontal and the cell pressure was 300 kN/m2. i. Draw the Mohr circle diagram representing the above stress conditions, and from it determine:− Coulomb’s equation for the shear strength of the soil, in terms of total stress;− the magnitude and obliquity of the resultant stress on the failure plane.
Three specimnens of clay having a small air-void content were tested in the shear box. Shear loading was started immediately after the application of the normal load and was completed in 8 minutes. The results are as follows: Normal Stress (kN/m2) Shear stress at failure (kN/m2) O Find the apparent cohesion of the clay. Find the angle of shearing resistance of the clay. What value of c would be obtained from an unconfined compression test on 145 241 337 103 117 131 the same soil?