Hot air enters a nozzle at pressure of 200 kPa and temperature of 700°C witha velocity of 70 m/s, and leaves at a pressure of 80 kPa. If the isentropicefficiency of the nozzle is 92%, calculate the exit velocity and temperature.For the average values of hot air take CprekJand y = 1.349kg.K= 1.11

Answered: Hot air enters a nozzle at pressure of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at 27 °C and 100 kPa enters in a steady flow to a nozzle at a velocity of 100 m/s. If the inlet area of the nozzle is 0.5 m², what is the mass flow rate through the system?
Consider an aircraft engine operating at subsonic conditions with a nozzle that has an exit area of 142in2 and a nozzle inlet/exit area ratio of 2. Engine gases flowing at 30lbm/s enter the nozzle with a pressure of 0.83 bar and avelocity of 144 m/s. The gases expand through the nozzle, exiting at the ambient pressure of 7.25 psia with a velocity of 1320 ft/s. a) For these conditions, what is the force (in units of lbf) trasmitted to the structure holding the nozzle. Provide both direction and magnitude of the force. b) Based on your results, comment on whether the force acting on the nozzle would hlep speed up or slow down a vehicle that used this nozzle as part of a jet propulsion system. I mostly wanted help in part b. Thank you.
Air at 500K and 800kPa enters a nozzle and drops to 205K and 98.5kPa at the exit. Since the air entering the nozzle is 25m/s and its mass flow rate is 0.9k/s; Calculate the velocity at the outlet, the inlet and outlet cross-sectional areas of the nozzle. (Assume that the air behaves ideally and DeltaH(kJ/kg)= 0.35 DeltaT.)
Air enters an ideal nozzle at a pressure of 45 psig with a temperature of 1,340°F The pressure at the nozzle exit is 14.925 psia. If the mass flow rate of air is 8 lb/min, determine the required exit diameter in cm
Question B3:A constant force of 71N is applied on a plunger pushing a piston of diameter 3cm through an insulted syringe containing air at 20°C (y = 1.4, R = 287J/kg- K). The exit diameter is of 2mm and the ambient atmospheric pressure is Pb = 101.3kPa. Estimate the temperature of the air leaving the syringe and the time needed to empty the syringe, given that at the beginning of the stroke the air chamber is 6cm long. The piston moves at a constant rate. Frictional losses may be considered negligible. %3D бст Рь — 101.3КPа F = 71N Зст 2mm Figure B3: Schematic representation of plunger-syringe arrangement.
Hi! I need help on how to solve this problem :) A nozzle is designed to expand air from 639 kPa and 32°C to 138kPa. Assume an isentropic expansion and negligible approach velocity. The air mass flow rate is 1.36 kg/s. Calculate the exit velocity. Ans. 465.2 m/s Thank you!
Nitrogen enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20 C. It leaves with a velocity of 15 m/s at an atmospheric pressure of 95 kPa. If the inlet diameter is 100 mm, the exit temperature is nearest
Q2/ The Air enters Diffuser at (80 kPa, 27°C) with velocity (200 m/s) and the flow rate (2.5 kg/s), and leaves the Diffuser at (42°C). The exit area of the diffuser is (400 cm2). Determine the exit velocity. from table T1=27.C=300K h1=300.19 kJ/kg T2=42.C%3D315K h2=315.27 kJ/kg
It is proposed that a nozzle receive air at 2 m/s, 300 K, and 150 kPa, attemperature of 280 K, and a velocity of 100 m/s. The mass flow rate is 0.1 kg/s. The surface of the nozzle is kept at 270 K. Assuming that the air behaves as an ideal gas with constant specific heats. Is this process possible?Given: Vel1 = 2 m/s, T1 = 300 K, P1 = 150 kPa, Vel2 = 100 m/s, T2 = 280 K, P2 = 110 kPa, dm/dt = 0.1 kg/s, Cp,air = 1.005 kJ kg-1 K-1
1- Air enters a nozzle at 0.2 MPa, 350 K, and a stagnation velocity. Assuming isentropic flow, determine the pressure and temperature of air at a location where the air velocity equals the speed of sound. What is the ratio of the area at this location to the entrance area?
What is the effect of friction on the entropy of the fluid during Fanno flow?
Air at 418.4°C enters a nozzle and exits at 482.4ms-1. Calculate the temperature at the exit. Give your answer in degrees Celsius. Take Cp=1.005kJkg-1K-1. Assume adiabatic behaviour.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS