Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.

Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.65P

See similar textbooks

Similar questions

mperature of nermocouple kg/m³, and an ideal gas 7-94 The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing over the duct with a velocity of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total power rating of the electronic devices that can be mounted into the duct. 7-97 flow If the initial is cor evaluate the 0.3 m of the initial cities of the 3D to the transt perform the from 1 to Treat me and the free stream Electronic o determine components inside 9 percent of tion of this 30°C 200 m/min 65°C Air 1.5 m on 20 cm FIGURE P7-94
The upper surface of a 1 mx 1 m ASTM B152 copper plate is being cooled by air at 20°C. The air is flowing parallel over the plate surface at a velocity of 0.1 m/s. The maximum use temperature for the ASTM B152 copper plate is 260°C (ASME Code for Process Piping, ASME B31.3-2014, Table A-1M). Determine the average convection heat transfer rate from the plate surface that is required to keep the plate surface temperature from going higher than the maximum use temperature. It is given that the properties of air at the film temperature of 140°C are (Table A-15) Pr = 0.7041, k= 0.03374 W/m-K, and v= 2.745 x 10-5 m²/s. The average convection heat transfer rate is W.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
ate the average wind velocity. & A 1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Alr a 25°C flows over the tank with a velocity of 7 m/s. Determine the rate of heat transfer to tank and the rate at which ice melts. The heat of fusion of water at 0°C is 333.7 K3RE
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates as shown in Fig 3. The gas at 220°C flows in parallel over the upper and lower surfaces of a 2-m-long flat plate at a velocity of 2 m/s. If the flat plate srface temperature is maintained at 80°C, de termine the local convection heat transfer coefficient at 1 m from the leading edge, the average convection heat transfer rate over the e ntire plate, and the total heat flux transfer to the plate. 11. 111. COo, T. Fig 3
Air flows through a long 5-cm diameter pipe at such a velocity that the Reynolds number is 105.The air enters the pipe at a temperature of 20°C. The first portion of the pipe is unheated and the velocity profile becomes fully developed in this portion of the pipe. The second portion of the pipe is heated to a uniform wall temperature of 40°C and has a length of 1.5 m. Determine total heat transferred through the 1.5 m long heated portion and show the variation of the wall heat transfer rate along the flow length of the pipe.
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and at 30°C flows with a velocity of 6 m/s over a 2.5-m * 8-m flat plate whose temperature is 120°C. Determine the rate of heat transfer from the plate if the air flows parallel to the (a) 8-m-long side and (b) the 2.5 m side.
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in parallel over the upper and lower surfaces of a 2.8-m-long flat plate at a velocity of 1.5 m/s and the flat plate surface temperature is maintained at 80°C. The properties of CO2 at Tf = (220°C + 80°C)/2 = 150°C are k = 0.02652 W/m∙K, ν = 1.627 × 10−5 m2/s, and Pr = 0.7445.Determine the total heat flux transfer to the plate. (Round the final answer to the nearest whole number.)
The local atmospheric pressure in Denver, Colorado (elevation 1610 m), is 83.4 kPa. Air at this pressure and at 30°C flows with a velocity of 4.8 m/s over a 2.3-m × 8-m flat plate whose temperature is 120°C. Determine the rate of heat transfer from the plate if the air flows parallel to the 2.3-m-side. The properties of air at 0.823 atm and at the film temperature of (120 + 30)/2 = 75°C are k = 0.02971 W/m·°C, ν = 2.486 × 10-5 m2/s, and Pr = 0.7166.
Air at 1 atm and 40°C is flowing over the top surface of a 0.2 m x 0.5 m-thin metal foil. The air stream velocity is 100 m/s and the metal foil is heated electrically with a uniform heat flux of 7500 W/m². If the friction force on the metal foil surface is 0.4 N, determine the surface temperature of the metal foil. Evaluate the fluid properties at 100°C.