How long does the asynchronous transmission of a 150 KByte (1 KByte = 1024 bytes) file take via a serial null modem cable with a transmission speed of U baud (U bit/sec)? Here, no parity, one start bit, 2 stop bits and eight data bits are to be used. Explain your answer or give the calculation method and determine the transmission time for U = 19,200 baud.

How long does the asynchronous transmission of a 150 KByte (1 KByte = 1024 bytes) file take via a serial null modem cable with a transmission speed of U baud (U bit/sec)? Here, no parity, one start bit, 2 stop bits and eight data bits are to be used. Explain your answer or give the calculation method and determine the transmission time for U = 19,200 baud.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose, you have 6 voice channels, each of 60MBPS. You have to use synchronous TDM to multiplex these channels. If 2 characters at a time are multiplexed (2 characters in each output slot), answer the following: What is the size of an output frame in bits? What is the output frame rate? What is the duration of an output frame? What is the output data rate? Input bit duration? Output bit duration? Output slot duration?
A corporation has a medium with a 7 MHz bandwidth (lowpass). The corporation needs to create 9 separate independent channels each capable of sending at least 12 Mbps. The company has decided to use QAM technology. What is the minimum number of bits per baud for each channel? What is the number of points in the constellation diagram for each channel? Let d = 0
We want to transmit 1000 characters with each character encoded as 8 bits. a. Find the number of transmitted bits for synchronous transmission. b. Find the number of transmitted bits for asynchronous transmission. c. Find the redundancy percent in each case.
The Asynchronous Transfer Mode (ATM) uses an 8-bit CRC for error detection. The 8 bit CRC uses the polynomial: x8+x2 + x1 + 1. a) Find the Generator bits G b) Find the CRC bits for a 16-bit input frame of 11100111 01010101.
III. The figure below shows synchronous TDM, the data rate for each input connection is 1 Mbps. If 1 bit at a time is multiplexed, Find (a) the input bit duration, (b) the output bit duration, (c) the output bit rate, and (d) the output frame rate. ... 1 1 1 1 1 1 Mbps 0 0 0 0 0 1 Mbps Frames 01010001110100010101 ... MUX 1 0 1 0 1 1 Mbps *** 0 0 1 0 0 1 Mbps
Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in Mbit/s (or Mbps), calculate the bit transmission Time Tb=1/R in microseconds . (Alternatively, you may calculate the symbol transmission time Ts=1/fSym¸where fSym is the symbol rate in baud.)
a. Compute for the data efficiency of transmitting if the data format is a General Synchronous Data Frame. b. For an asynchronous data transmission (wherein 1 byte of data is accompanied by a specific number of auxiliary bits), how many start and stop bits are there if the data efficiency in transmitting is ? The number of start bits is equal to the number of stop bits.
4. Using a combination of ASK, FSK and PSK: b) Sketch the transmitted signal for the following bit stream: 10110011 01110100 11000001 c) What would be the data rate of this system if 20,000 signals were sent per second? d) What would be the effective bit time (not the signal time)? e) Could this be sent on a channel with a signal to noise ratio of 20 dB and bandwidth of 11,000 Hz?
For the following stream of digital signal which is being transmitted by bit rate 5 Kbps: 101100000000110 a) Draw the waveform for all line codes you studied. b) Determine if the line code is self synchronized or not. c) Determine if the code can be used with ac coupling or not d) Determine the Bandwidth of the line code e) Which code is used in magnetic recording f) Which code is used in LAN
Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data frames carry a useful payload of size 12,000 bits. Assume that both ACK and data frames have 320 bits of header information, and that ACK frames carry no data. What is the effective data throughput When using Stop and Wait?
A person want to transmit the data 1100110 to his friend using hamming code technique. Calculate (i) number of redundant bits required to transmit the data (ii) positions of redundant bits (iii) total code length (iv) the transmitted hamming codeword (v) If during transmission, the 5th bit is flipped. Explain the process of recovering origin data from the received data
The Asynchronous Transfer Mode (ATM) uses an 8-bit CRC for error detection. The 8 bit CRC uses the polynomial: x8+x2 + x1 + 1. a) Find the Generator bits G b) Find the CRC bits for a 16-bit input frame of 11100111 01010101 Need solution regarding part 2