HW#2 Example 2.26: A single-acting triplex pump of an output power of 1,250 hp is used to deliver the required rate at running speed of 110 strokes/min. The liner size and length are 5.5 and 30 inches, respectively. If the displacement efficiency is 90%, calculate the discharge pressure of the pump at that speed.

HW#2 Example 2.26: A single-acting triplex pump of an output power of 1,250 hp is used to deliver the required rate at running speed of 110 strokes/min. The liner size and length are 5.5 and 30 inches, respectively. If the displacement efficiency is 90%, calculate the discharge pressure of the pump at that speed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
A•, PK/s ull E ZAIN IQ Asiacell د واجب الفصل الثا. . . A single stage centrifugal pump has an impeller of 250 mm diameter which rotates at 1,800 rpm and lifts 60 lit/sec to 25 m with an efficiency of 70%. Obtain the number of stages and diameter of each impeller of a similar multi-stage pump to lift 75 lit/sec to 175 m at 1,500 rpm. (8 stages ; 280 mm dia) The impeller of a centrifugal pump has an outer diameter of 35 cm and runs at 1,000 rpm. The blades are bent at 150° to the direction of motion at discharge and the radial velocity of flow is constant through the impeller at 2'5 m/sec. The measured head across the pump is 20 m and the frictional resistance of the pump is estimated to be 2 m. Find the efficiency according to velocity triangles. (76'4%)
A single stage centrifugal pump has an impeller of 250 mm diameter which rotates at 1,800 rpm and lifts 60 lit/sec to 25 m with an efficiency of 70%. Obtain the number of stages and diameter of each impeller of a similar multi-stage pump to lift 75 lit/sec to 175 m at 1,500 rpm. (8 stages ; 280 mm dia)
4.3 A centrifugal pump is required to develop a pressure rise of 30 psi when delivering 1000 gpm. If three motors with 2000, 3600, and 4200 rpm are available, which motor should be used for maximum efficiency? What are the approximate impeller diameter and the pump efficiency? Should a double-suction pump be considered?
Find the specific speed of a double suction centrifugal pump delivering 1.5 m³/s against a net head of 15 m when running at 725 r.p.m. state the type of impeller to be employed for this pump.
An axial flow pump discharges water at the rate of 78 m³/min and runs at 550 rpm. The total head is 10 m. Assume blade velocity of 22 m/s, flow velocity of 4.5 m/s, hydraulic efficiency of 0.87, and overall pump efficiency of 0.83. Calculate Cr OP 3.1. The power delivered to the water, and power input The impeller hub diameter and tip diameter 3.2. 3.3. The inlet and outlet blade angles for the rotor 30 07:30 S
A submersible pump of 80 percent efficiency is used in pumping water with flow rate,Q from a river to a pool at an elevation, h. The frictional losses is assumed with losscoefficient, K = 10. By the aid of a labelled diagram, derive an expression on thepower require to drive the pump.
A "spa tub" is to be designed to replace bath tubs in reno- vations. There are to be 6 outlet nozzles, each with a di- ameter of 12 mm, and each should have an outlet velocity of 12 m/s. What is the required flow rate from the single pump that supplies all of these nozzles? If there is one suction line leading to the pump, what is the minimum diameter to limit the velocity at the inlet of the pump to 2.5 m/s?
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet. The inlet pressure is 4-in Hg above atmospheric and the discharge pressure is 29 psia. Assume the pump input is 8 hp, if the pump has an 8-inch diameter inlet and a 4-inch diameter discharge: 1.How much pressure loss in the pump? a. 28.4 ft-lbf/lb b. 5 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 2. How much is the velocity loss in the pump? a. 28.4 ft-lbf/lb b. 45.3 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 3. If the pump speed is increased from 1600 to 2400 rpm, what will be the new net flow rate in the pump? a. 800 gpm b. 1050 gpm c. 1400 gpm d. 1965 gpm 4. Find the new brake horse power if the pump speed in increased from 1600 to 2400 rpm. a. 64 hp b. 20.25 hp c. 8 hp d. 30.375 hp
QUESTION 1:A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300kW (shaft power) and rotates at 96.3 rad/s. The flow rate generated by the machine is54.7 Kilo-litres/min. The impeller blade inlet angle and width is 23° and 180 mmrespectively. The blades occupy 12% of the impeller area and the water is assumed toenter the impeller radially. Suction and delivery pipes are equal in size.Determine:1.1The impeller inlet (i) diameter and inlet blade velocity.(Hint - Substitution: ln in terms of D and U, in terms of D, both sub into Tan of Blade inlet angle,only unknown is then solving for Dz)1.2.If the pump has a mechanical efficiency of 80%, calculate the blade velocity atoutlet (U.) and outlet whirl velocity Vw.. Assume the blade exit angle equal to theguide vane angle. (Hint - Substitution: Write Vw in terms of U, sub in Euler equation onlyunknown then is solve for Vwo)1 3Impeller outer diameter.1.4,If the flow through velocity is consistent through the…
Refer to the “composite performance chart” for a Goulds 3x4-10centrifugal pump operating at 1750 rpm. It shows the pump performance curve for 5 differentimpeller sizes, but also shows the HP required, efficiency, and NPSH required at differentoperating points.Describe the performance of this pump, using an 8 inch impeller and a required flow rate of175 gpm. Give head available, power required (BHP), efficiency, and NPSH req’d. What is the water horsepower (WHP)?