hydraulic pump increases the pressure in a system from 500 kPa to 3 MPa at a flow rate of 2 e/s. The uid density is 820 kg/m³. A shock loss over the pump is 0, 8 m, assume the inlet and outlet of the pump t the same level and have the same diameter. Determine the mechanical power required to drive a ump with a mechanical efficiency of 80%.

hydraulic pump increases the pressure in a system from 500 kPa to 3 MPa at a flow rate of 2 e/s. The uid density is 820 kg/m³. A shock loss over the pump is 0, 8 m, assume the inlet and outlet of the pump t the same level and have the same diameter. Determine the mechanical power required to drive a ump with a mechanical efficiency of 80%.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator BC in deg/s. L = 1.38 m 2L2 = 1.15 m 2L2 - Li --- L2 -
Q1 Glycerine (u = 150 Pa.s and p 1260 kg/m³) flows at a velocity of 5.0 m/s in a 10 cm diameter pipe. Estimate: (a) the boundary shear stress in the pipe due to the flow (b) Head loss in a length of 12 m of pipe and (c) Power expended by the flow in a distance of 12 m.
0.12 O -0.12 8.33 (1) Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. O-8.33 -L h e - - - -
(a) Glycerine at 25 °C flows through a straight copper tube (D = 73.8 mm), at a flow rate of 180 L/min. Calculate the pressure difference between 2 points which are 25.8 m apart, if the first point is 0.68 m below the second point. Gven: At 25 °C density and dynamic viscosity for glycerine is 1286kg/ and 0.96 Pa.s respectively(b) If benzene at 50 °C is used in question (a) above instead of glycerine, evaluate the new pressure difference. ...
(4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 °C. The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is 0. 07 L / D) V? H. D=20 cm, the rate of flow is 0.0 a=1 ase calculate the 2g pressure in the pipe. Elevation = 100 m Elevation = 20 m L=2000 m %3D II ||
O -0.13 Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 24 inches, hydraulic head at (2) is 11 inches, and the travel distance is 100 inches. O 7.7 O -7.7 (1) O 0.13 e - - - -
-8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. h (2) e - - - -
A cylindrical tank with its axis horizontal has a length of 6 m and the ends of the tank are vertical planes, as shown in Figure Q2 (a). The vertical pipe of 0.2 m in diameter is connected to the top of the tank. The tank and the pipe are filled with ethyl alcohol to a level of 1.5 m above the top of the tank. The diamter is 2.07m.
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
Civil Engineering Water flows through two different pipes A and B of the same circular cross- section but at different flow rates. The length of pipe A is 1.0 m and that of pipe B is 2.0 m. The flow in both the pipes is laminar and fully developed. If the frictional head loss across the length of the pipes is same, the ratio of volume flow rates QB/QA is _(round off to two decimal places)
Water at 20°C is pumped at a rate of 15 L/s into a reservoir as shown in the Figure below. Between the pump and the reservoir is 150 m of 100 mm diameter PVC pipe, and the water surface elevation in the reservoir is 8 m above the centerline of the inflow pipe. The roughness height of the PVC pipe can be assumed to be negligibly small. Estimate the gauge pressure (kPa) on the downstream side of the pump. 15 L/s 133 120 111.7 131.5 Pump P - 150 m. 100 mm Reservoir 8m
d) A nozzle, which reduces from 45mm to 30mm in diameter, discharges water at a rate of 30 L/s. If the pressure at the entrance to the nozzle is 800 kPa and 50 kPa at the outlet, determine the force on the nozzle.