i just need final answer A coaxial capacitive sensor is desired to measure the water level in a water tank. The coaxial sensor with a length of d=32 cm has an inner radius of a=9 mm and an outer radius of b=12 mm. Since the total capacitor value is measured at the sensor output 4.03 nF, the water level l =? Calculate (Note: It is known that the water temperature in the tank is 20 degrees. The variation graph of the relative dielectric constant with temperature is also given below.) a- 15cm b- 12cm c- 21cm d-18cm e- 26cm

i just need final answer A coaxial capacitive sensor is desired to measure the water level in a water tank. The coaxial sensor with a length of d=32 cm has an inner radius of a=9 mm and an outer radius of b=12 mm. Since the total capacitor value is measured at the sensor output 4.03 nF, the water level l =? Calculate (Note: It is known that the water temperature in the tank is 20 degrees. The variation graph of the relative dielectric constant with temperature is also given below.) a- 15cm b- 12cm c- 21cm d-18cm e- 26cm

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.1: Cnc Basics

Problem 2RQ: What is an MCU and what is its function?

See similar textbooks

Similar questions

Q1: 1. What's the main purpose of using sensor/transducer unit in mechatronics systems? * Your answer Q1: 2. What's the main purpose of using signal processing device with sensor/ transducer? *
What is the difference between OrCad and Comsol multiphysics
Conventional float actuated device is used as a level measurement sensor, which consist of pulley and a pointer which move over a graduated scale. Let say you are asked to develop a controller-based float actuated system having a sensor for level measurement or may be more than one sensor is required for accurate level measurement, which sensor will you use and why? Draw the whole schematic showing the position of the sensor or sensors. Will pulley be part of your new digital system, if yes justify your answer, if no, then how you will develop a system without using pulley.
[2.2] Consider two different implementations of the same instruction set architecture. instructions can be divided into four classes according to their CPI (classes A, B, C, and D with a clock rate of 2.5 GHz and CPIs of 1, 2, 3, and 3, and P2 with a clock rate of 3 GHz CPIs of 2, 2, 2, and 2. Given a program with a dynamic instruction count of 1.0E6 instruc divided into classes as follows: 10% class A, 20% class B, 50% class C, and 20% cla which is faster: P1 or P2? a. What is the global CPI for each implementation? Ans. 2.6, 2.0 b. Find the clock cycles required in both cases. Ans. 26 x 105, 20 × 10³
Dive into Microchip's involvement in automotive electronics and safety-critical systems. How are their products used in automotive applications, and what safety standards do they comply with?
SOLVE STEP BY STEP IN DIGITAL FORMAT Explain some methods to improve the efficiency of aircraft propulsion systems, as well as combustion techniques or the use of alternative fuels.
و واجب تصصيم.pdf x 21- ale - la ay de aLis yae li leslal aie paai B x Machine Design - Eng. Peter - Se C:/Users/MI/Desktop/i20%als-pdf LCD Custom Charac. O Share | Home Page O B الفصول الدراسية تحويل JPG إلى .- PDF YouTube Gmail M 100% 3 / 1 واجب تصميم.pdf 4.5 The principal stresses induced at a point in a machine component made of steel 50C4 (Sy = 460 N/mm2) are as follows: Oj = 200N/mm² Calculate the factor of safety by (i) the maximum shear stress theory, and (ii) the distortion energy theory. 0, = 150 N/mm? 03 =0 %3D [(1) 2.3 (ii) 2.55] 09:35 AR
"Design and Fabrication of an Agricultural Spraying Attachment foran Autonomous Rover"we need help in the machine design part of our study, specifically Pump selection, batteryselection, and center of gravity computation. Rover weight capacity 35 kilo grams (payload)Rover measurements:Wheel distance - 14.5 inches and 8.5 inchesRover platform size (width & length) 14.4 inches x 10.4 inchesHeight- 15.8 inches. ....help it
BT - F X A Some X Mech X E Blank X U Some X (4) W X V Accor AlpQLSespFLR_U8a1ISgmucPg8mqSkCgmsdnT2tb3o0QG5MQMUc5rg/viewform?hr_submission%=DCH 2 Maps GE News 14 JIIT University Noid... Plus One English Te.. NPTEL :: Mathemati... U Clear selection 1 point Q.14. A mass of 35kg is suspended from a weightless bar AB which is supported by a cable CB and a point at A as shown in figure. Pin reactions at A on the bar AB are 275 mm R(x)=343.4 N, R(y) =755.4N R(x)=343.4 N, R(y)=0 R(x)=755.4 N, R(y)=343.4N R(x)=755.4 N, R(y)=0 Clear selection Q.15. A string 2 m long is tied to the ends of a uniform rod that weighs 60 N 1 point and 1.6m long. The string passes over a nail so that the rod hangs 32% 近 O O
Sensor systems for obstacle detection and avoidance in mobile robots. • Design and develop a suitable processor-based Data Acquisition (DAQ) system and external hardware to interface, measure, display and store the responses from the selected sensors. • Characterize and evaluate the sensor performance use real data already collected or extrapolated information from the sensor datasheets.
Describe the principles of operation of a 3D motion controller (e.g., Leap Motion) and discuss its potential applications beyond traditional input devices.
Mechatronics Components and Instrumentation MECT361 please write the answer in keypord and please don't late ??