Help please Required informationIn a certain medical application, water at room temperature and pressure flows through a rectangular channel of length L =22 cm, width s = 2.6 cm, and gap thickness b = 0.3 mm as shown in the diagram below. The volume flow rate is sinusoidalwith amplitude Q = 0.50 mL/s and frequency f = 20 Hz, i.e., Q = Q sin (2Tft ). Assume that v = 1 x 10 6 m2/s and u =0,001 Pa-s.b.Calculate the maximum Reynolds number (Re = Vb / u) based on maximum average velocity and gap thickness. Channel flow like thisremains laminar for Re less than about 2000. If Re is greater than about 2000, the flow will be turbulent.The Reynolds number is17of 17Next >Prev16

Answered: Image /qna-images/answer/15608153-534e-4e85-8b87-ed160297c7e3.jpg

In a certain medical application, water at room temperature and pressure flows through a rectangular channel of length L = 22 cm, widths= 2.6 cm, and gap thickness b = 0.3 mm as shown in the diagram below. The volume flow rate is sinusoidal Q sin (21ft ). Assume that v =1 x 10 m2/s and p = with amplitude Q = 0.50 mL/s and frequency f = 20 Hz, i.e., Q = 0.001 Pa-s.

In a certain medical application, water at room temperature and pressure flows through a rectangular channel of length L = 22 cm, widths= 2.6 cm, and gap thickness b = 0.3 mm as shown in the diagram below. The volume flow rate is sinusoidal Q sin (21ft ). Assume that v =1 x 10 m2/s and p = with amplitude Q = 0.50 mL/s and frequency f = 20 Hz, i.e., Q = 0.001 Pa-s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A storage tank contains a liquid at depth y where y= 0 when the tank is half full. Liquid is withdrawn at a constant flow rate Q to meet demands. The contents are resupplied at a sinusoidal rate 3Q sin'(t), The outflow is not constant but rather depends on the depth. For this case, the differential equation for depth is shown below. Some variable values are A = 1200 m?, Q = 500 m /d, and a (force function) = 300. Arrange the variables into the Mathematical Model format: stating which variable(s) is dependent, independent, etc. dy a(1+ y)15 dx A Figure P1.7
On a circular conduit there are different diameters: diameter D1 = 2 m, changes into D2 = 3 m. The velocity in the entrance profile was measured: v1 = 3 m/s. Calculate the discharge and mean velocity at the outlet profile (see figure below). Determine also type of flow in both conduit profiles (whether the flow is laminar or turbulent) – temperature of water T = 12° C. (use Reynold's number Re), For laminar flow: Re2320, Kinematic viscosity of water of 12°C, v is equal to 1,24 10^-6 m2/s %3D %3D VD, D2 Figure
On a circular conduit there are different diameters: diameter D1 = 2 m, changes into D2 = 3 m. The velocity in the entrance profile was measured: v1 = 3 m/s. Calculate the discharge and mean velocity at the outlet profile (see figure below). Determine also type of flow in both conduit profiles (whether the flow is laminar or turbulent) – temperature of water T = 12° C. (use Reynold’s number Re), For laminar flow: Re<2320, For turbulent flow Re>2320, Kinematic viscosity of water of 12°C, v is equal to 1,24 10^-6 m2/s.
(Q29) A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure intensity in large pipe is given as 14 N/cm2 and the flow velocity in the larger pipe is 2 m/s. Find:- (a) The rate of flow of water through a horizontal pipe. (b) Loss of head due to sudden contraction. (c) Pressure intensity in smaller pipe.
G1/ In the fig.shown, the Flow rate Pipe (A) is equal ( QA = 25 Lit15), the diameter is equal ( DA = 75 mm, D, = De = Dc =30mm), and the velocity in Pipe (D) is equal (Uo=5 m/s), the relation between flow rate in in 6o mm, Pipe (B) and pipe (c) GB =3 Qc. Find the Value of '. Re, Qc, Qo. 2- UA, UB, Uc: Pe = 30 mm water Pc = 30mm imput QA = 25 2i+/sec OA= 75 mm = 6o mm input = A outPut = B, C, D accumulation = o.
1. Find the flow distribution in the three-parallel pipe system shown in figure below. Take Qin = 2500 L/min. Element L, m D, mm fo EK lin 1 50 75 0.02 2 2 80 85 0.03 4 3 3 120 100 0.025 2 Ans: Q₁ = 731 L/min, Q₂ = 790 L/min, Q₂ = 979 L/min * M
* Q4// In fig shown the pipe line have (QA=15 L/s),(DA=100mm), (DD=50mm),, (DB-DC=25mm), (QB=3QD), (uc=4m/s), Calculate the following using Sl units: 1- The velocity (U) in pipes (B); 2-The Volumetric flow rate(Q) in pipe (D). ; 3- The type of flow in pipe (A,B,C,D) ; 4- The mass flow rate (m.) in pipe (A,B,C,D). ; note that: DA,DB,DC,DD = diameter ; kinematics viscosity 0.0001 m2/s; dynamic viscosity 0.088 kg/m.s. B A Water 0 C
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (2) Select all energy loss types between section 1 and 2_________ A. Minor loss for the two elbows B. Friction loss in suction line C. Minor loss for Valve 1 D. Entrance loss E. Exit loss F. Friction loss…
A hydraulic pump is shown in the following Figure, flow rate is 25 L/min, the diameter of suction pipe is 30mm, and the suction port of pump is higher than the oil surface of tank, h=300mm. Kinematic viscosity of oil is 30x10-“m²/s, density of oil is 900kg/m³. If only the pressure loss along the straight suction pipe with length 400mm is considered 75 (1 = a = 2, g=9.8) R. (1) Calculate the flow velocity in the suction pipe; (2) Judge the flow state in suction pipe; (3) Calculate the pressure loss along the straight suction pipe; (4) Calculate the vacuum degree of suction port.
What is the velocity (m/s) at section 4, if the d4=10.4 cm? The problem is steady and incompressible. 2 d=3 cm V=4 m/s water d= 4 cm V= 2m/s discharge=0.005 mis A9 N
338 B/s O 1: 56% E 3:01 Question: Gasoline is flowing through this 180° pipe bend. The pipe cross-sectional area is 18 in?. Take the pipe weight as 5 Kg. Flow rate is 0.5 liters/s. Pressure at section-1 6 psia, pressure at section-2 is 4 psia. Calculate the anchoring force required to hold this pipe and also show its direction, referenced to proper 2-dimensional a cartesian coordinate system. (2 1